manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 455

Test Results

NetBlazer

443

Traces - OTN

Traces - OTN 

From the

 Test

 menu, tap 

Results

,

Traces

, and the 

OTN

 sub-tab. 

OTUx, ODUx, and TCM Buttons 

Tap on either OTUx, or an ODUx button. For ODUx when TCM is enabled 
(see Modify TCM on page 257), tap on a TCMx button to select a TCM level. 

SM/PM TTI Traces 

Note:

The TTI Traces are configurable for SM (OTUx), PM (ODUx), and TCM 
(ODUx when TCM is enabled; refer to 

Modify TCM

 on page 257).

Received Message

SAPI

 indicates the received TTI (Trail Trace Identifier) Source Access 

Point Identifier. 

DAPI

 indicates the received TTI Destination Access Point Identifier. 

Operator Specific

 indicates the received TTI Operator Identifier. 

Expected Message

Note:

The following settings are coupled with the Expected Message from 

Traces - 

OTN

 on page 443.

SAPI

 allows editing the expected Source Access point Identifier (TTI 

bytes 1 to 15). Available when the SAPI OTU/ODU-TIM check box is 
selected. The default setting is 

EXFO OTU SAPI

 for OTUx, and 

EXFO 

ODU SAPI

 for ODUx. The TTI byte 0 is set to NULL (all 0’s). 

DAPI

 allows editing the expected Destination Access point Identifier 

(TTI bytes 17 to 31). Available when the DAPI OTU/ODU-TIM check box 
is selected. The default setting is 

EXFO OTU DAPI

 for OTUx, and 

EXFO 

ODU DAPI

 for ODUx. The TTI byte 16 is set to NULL (all 0’s). 

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands