manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 320

Test Results

308

FTB-700G/800 Series

Alarms/Errors

Undersize 

RX

: Frames smaller than 64 bytes with a valid FCS. 

Oversize Monitoring

 check box, when selected (cleared by default), 

allows monitoring the 

Oversize

 frame errors. 

The following errors are only available with 

Half Duplex

 mode (only for 

electrical interface at speeds of 10 Mbit/s and 100 Mbit/s). 

Collision

 

RX

: Indicates the number of collisions on the link. 

Late Coll. 

RX

: Indicates the number of collisions that have occurred after a 64 

bytes transmission.

Exc. Coll. 

RX

: Indicates the number of frames that were sent 16 times 

unsuccessfully due to consecutive collisions.

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands