manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 434

Test Results

422

FTB-700G/800 Series

Summary (Link OAM)

Dying Gasp

: Indicates that the OAM link partner has sent an 

unrecoverable local failure notification (bit 1 of the Flags field is set 
to 1). 

Link Fault

: Indicates that the OAM link partner has sent a link fault 

notification (bit 0 of the Flags field is set to 1). 

Loopback 

Local

 indicates the 

Status

 of the local loopback (

Enabled

 or 

Disabled

) and allows to 

Enable

 or 

Disable

 it. 

Remote

1

 indicates the 

Status

 of the remote loopback (

Enabled

 or 

Disabled

), the number of 

Successful

 remote loopback requests, the 

number of 

Fail

 remote loopback requests, and allows to 

Enable

 or 

Disable

 it. 

OAMPDU Frame Count

Indicates the number of transmitted and received OAMPDU frames of 
the following types: 

Information

 

Loopback Control

 

Event Notification

 (received only) 

Total

 indicates the total number of transmitted and received OAMPDU 

frames. 

1. Statistics are influenced by both the protocol (Parser Action is set to “01”) and physical loopback. The Fail and 

Successful counters will be affected by successive enable/disable loopback requests when sending loopback request 

to a remote FTB-700G/800 Series module running Link OAM test since it does not provide physical loopback. 

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands