manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 196

Test Setup - Test Configurator, Timer, and System

184

FTB-700G/800 Series

MAC/IP/UDP

UDP 

Allows the selection of the source and destination UDP port number. 

Source Port

 is configurable from 

0

 to 

65535

; the default is 

49184

. 

Destination Port

 is configurable from 

0

 to 

65535

; the default is 

7 (echo)

. 

TCP 

Allows the selection of the source and destination TCP port number. 

Source Port

 is configurable from 

0

 to 

65535

; the default is 

49184

. 

Destination Port

 is configurable from 

0

 to 

65535

; the default is 

7 (echo)

. 

Payload

For RFC 2544 and EtherBERT, indicates that the frame structure contains a 
Payload. 

For Traffic Gen & Mon, allows the selection of both user defined header 
and pattern. Payload is not configurable when the 

QoS Metrics Tags 

Insertion

 check box is selected (see the 

Global

 tab).

User Defined Header

 check box when selected (cleared by default) 

allows to define a 16-byte header. 

Pattern

 allows the selection of a pattern: 

00

 to 

FF

 (default is 

CC

).

FCS

Indicates that the frame structure contains an Ethernet FCS. 

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands