EXFO FTB-1 User Manual Download Page 452

Page: 452 / 675

Test Results

440

FTB-700G/800 Series

Summary (TCP Throughput)



TCP Throughput

displays respectively the last, minimum, maximum,

and average TCP Throughput measurement.



Window Size

displays respectively the last, minimum, and maximum

TCP window size.



Round Trip Latency (ms)

displays respectively the last, minimum,

maximum, and average round trip time gathered from the TCP
Throughput test.

Ethernet Traffic

Note:

See

Traffic - Ethernet

on page 446 for more information.

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for FTB-1

Reviews:

Brands by name

Popular brands

EXFO FTB-1, User Manual

Search results

Summary of Contents for FTB-1

Reviews:

Brands by name

Popular brands