manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 441

Test Results

NetBlazer

429

Summary (RFC 6349)

Buffer Delay (%)

 indicates the Buffer Delay percentage metric which 

represents the increase in RTT during a TCP Throughput test versus the 

Minimum RTT

. 

TCP Throughput Threshold (% of ideal)

 allows to enter the TCP 

Throughput as a percentage of the defined CIR that will be used to 
declare the pass/fail verdict for both directions: 

0

 to 

100

%; default is 



%. The calculated throughput based on the selected threshold is 

displayed for both directions. 

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands