manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 198

Test Setup - Test Configurator, Timer, and System

186

FTB-700G/800 Series

Network

IP

IP Version

 allows the selection of either 

IPv4

 (default) or 

IPv6

. Only IPv4 is 

supported for TCP Throughput test application. 

For 

IPv4

 the following configuration parameters are available. 

Automatic IP (DHCP)

 check box, when selected (cleared by default), 

allows to dynamically obtain an IP address from a DHCP (Dynamic 
Host Configuration Protocol) server. 

IP Address

1

: Enter the IP address of the port. The default setting is 

10.10.x.y, where x and y are respectively the two least significant bytes 
of the port default MAC address. 

Subnet Mask

1

: Enter the Subnet Mask. The default setting is 

255.255.000.000

. 

Default Gateway

1

 check box, when selected (cleared by default), 

allows to enter a default Gateway IP address. When the 

Default 

Gateway

 check box is selected, its default address is 

0.0.0.0

. 

1. Not configurable when the 

Automatic IP (DHCP) 

check box is selected.

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands