Home
/
EXFO
/
FTB-1
/
User Manual

EXFO FTB-1, User Manual

Share

Page: 459 / 675

EXFO FTB-1 User Manual Download Page 459

Test Results

NetBlazer

447

Traffic - Ethernet



Unicast

indicates the number of unicast frames transmitted/received

without FCS errors.



Non-Unicast

indicates the number of multicast and broadcast frames

transmitted/received without FCS errors.



Total

indicates the total number of all frames transmitted/received

without FCS error.

Frame Size

Displays the RX count of each received frame size (valid and invalid), and
the percentage (%) ratio of each received frame size based on the total
count of frames. The the percentage (%) ratio is not available for Through
Mode test application.



< 64

: frames with less than 64 bytes.



64

: frames equal to 64 bytes.



65 - 127

: frames from 65 to 127 bytes.



128 - 255

: frames from 128 to 255 bytes.



256 - 511

: frames from 256 to 511 bytes.



512 - 1023

: frames from 512 to 1023 bytes.



1024 - 1518

: frames from 1024 to 1518, or 1522 (1 VLAN tag),

1526 (2 VLAN tags), or 1530 (3 VLAN tags) bytes.



> 1518

: frames with more than 1518, or 1522 (1 VLAN tag),

1526 (2 VLAN tags), or 1530 (3 VLAN tags) bytes.



Total

indicates the total count of all received frames (valid and invalid).

«
...
457
458
459
460
461
...
»

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands