manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 537

Test Functions

NetBlazer

525

Spare Bits

RX

E4

G.751 Bit 14, 15, 16 

are reserved for national use. 

E3

G.751 Bit 12

 is reserved for national use. 

E2

G.742 Bit 12 

represents Bit 12 from Timeslot 1, 2, 3, and 4 respectively. 

E1

S

i0

 is located in the bit 1 of the frame containing the frame 

alignment signal (FAS). 

S

i1

 is located in the bit 1 of the frame not containing the frame 

alignment signal (FAS). 

S

a4

 to 

S

a8

 are located in bit 4 to 8 of frame number 1, 3, 5, and 7 of 

sub-multiframe 1 and 2. Possible values are either 

0

 and 

1

 or 

0000

 

to 

1111

 depending on the framing. 

TS16 Frame 0 Bit 5, 7, 8 

are located in bit 5, 7, and 8 from Timeslot 

16 of frame 0 of a E1 signal. 

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands