manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 199

Test Setup - Test Configurator, Timer, and System

NetBlazer

187

Network

For 

IPv6

 the following configuration parameters are displayed: 

Link-Local 

IPv6 Address

, 

Global IPv6 Address

, and 

Default Gateway

. Tap on the 

Config

 button to access all settings. 

Link-Local IPv6 Address

 (LLA) is used for local communication 

between on-link neighbors and for Neighbor Discovery process. 

Mode

Stateless Auto

 (default) allows automatic generation of the IPv6 

address based on the MAC address. 

Static

 allows to enter the IP Address. 

Address

, available with 

Static

 mode, allows to select the 

Link-Local IPv6 Address. The accepted range is from 

FE80:0000:0000:0000:0000:0000:0000:0000

 to 

FE80:0000:0000:0000:FFFF:FFFF:FFFF:FFFF.

 The default address 

is

 FE80::[Interface ID]

, where [

Interface ID

] is generated from 

the source MAC address. When the 

Address

 field is selected for 

editing using virtual keyboard, the 

Previous IPs

 button appears 

allowing to select a previously configured IP address. 

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands