EXFO FTB-1 User Manual Download Page 592

Page: 592 / 675

Glossary

580

FTB-700G/800 Series

Acronym List

European standard for digital transmission-level 0 (64 Kbit/s).

European standard for digital transmission-level 1 (2.048 Mbit/s).

European standard for digital transmission-level 2 (8.448 Mbit/s).

European standard for digital transmission-level 3 (34.368 Mbit/s).

European standard for digital transmission-level 4 (139.264 Mbit/s).

Errored Block

EBS

Excess Burst Size

Error Count

ECN

Explicit Congestion Notification

ECT

ECN Capable Transport

EEC

Ethernet Equipment Clock

EFS

Error Free Second

eHEC

extension Header Error Check

EIR Excess

Information

Rate

EoOTN

Ethernet over OTN

ERDI

Enhanced RDI

Errored Second

ESMC

Ethernet Synchronization Message Channel

ESF

Extended Superframe

ESR

Errored Second Ratio

EUI

EXFO Universal Interfaces

EXI

Extension Header Identifier

EXM

Extension Header Mismatch

EXT CLK

External Clock

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for FTB-1

Reviews:

Brands by name

Popular brands

EXFO FTB-1, User Manual

Search results

Summary of Contents for FTB-1

Reviews:

Brands by name

Popular brands