manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 149

Test Setup - Test Configurator, Timer, and System

NetBlazer

137

EtherSAM - Global

EtherSAM - Global 

From the 

Test

 menu, tap 

Setup

, 

Test Configurator

, tap on the test block, 

and on the 

Global

 tab. 

Dual Test Set 

Dual Test Set 

(

DTS

) check box when selected (cleared by default) 

enables EtherSAM 

Dual Test Set

. Once 

Dual Test Set

 is enabled, use 

the 

Discover Remote

 button to select a remote unit.  

Note:

Alternatively it is possible to use the Discover Remote button to connect to a 
remote module and automatically enable the Dual Test Set. For more 
details, refer to 

Discover Remote Button

 on page 530. 

Disconnected

 indicates that there is no connection established with a 

remote module. 

Connected

 indicates that the connection is established with a remote 

module. 

Discover Remote

 button allows to discover remote modules 

supporting 

Remote Loopback

 and/or 

Dual Test Set

. For more details, 

see 

Discover Remote Button

 on page 530. 

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands