manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 477

Test Functions

NetBlazer

465

FDL - Performance Report Message

Received Messages

Event Counts

 lists received PRM bit event counts.See 

PRM Bit Events

 

below. 

Report Content

 lists received performance information. See 

Performance Information

 below.

Circuit

 indicates the selected circuit type: 

CI to Network

 or 

Network to CI

. 

Valid Event Count

 indicates the number of valid PRM messages 

received. 

Link Activity

, see page 462 for more information. 

PRM Bit Events

 table, available when the 

Event Counts

 button is 

selected, reports the count of the detected valid PRM bit events. 

G1: CRC = 1
G2: 1 < CRC 

 5

G3: 5 < CRC 



10

G4: 10 < CRC 

 100

G5: 100 < CRC 



319

G6: CRC 

 320

SE: Severely errored framing 

 1

FE: Frame sync. bit error 

 1

LV: Line Code Violation 

 1

LB: Payload loopback activated
SL: Slip 

 1

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands