EXFO FTB-1 User Manual Download Page 72 | Manualshive

Page: 72 / 675

EXFO FTB-1 User Manual Download Page 72

Test Setup - Test Applications

60

FTB-700G/800 Series

Smart Loopback

Smart Loopback

Allows transmitting back the received Ethernet stream of data while
interchanging the source and destination MAC addresses, IP addresses,
and/or UDP/TCP ports. However in

Transparent (Pseudo-Physical

) mode

the Smart Loopback operates as a physical loopback by transmitting all
received frames unaltered and without discrimination.

The Smart Loopback test can be created locally (refer to

Ethernet Test

on page 78) or remotely using an EXFO unit (refer to

Remote Button

on page 530) or a Third-Party device (see

Remote Loopback



Typical Smart Loopback test application:



Supported Interfaces/Rates: 10M to 10G LAN/WAN.

Network

under test

Testing Unit

Smart Loopback Unit

FTB-700G/800 Series

FTB-700G/800 Series

«
...
70
71
72
73
74
...
»

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands