manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 456

Test Results

444

FTB-700G/800 Series

Traces - OTN

SAPI OTU/ODU-TIM

 check boxes, when selected (cleared by default), 

allows editing the expected Source Access Point Identifier (SAPI) and 
also enables OTU/ODU-TIM alarm monitoring. 

DAPI OTU/ODU-TIM

 check box, when selected (cleared by default), 

allows editing the expected Destination Access Point Identifier (SAPI) 
and also enables the OTU/ODU/TCM-TIM alarm monitoring. 

Copy RX

 uses the received SAPI/DAPI message as the expected 

SAPI/DAPI message. 

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands