manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 671

Index

NetBlazer

659

DAPI TCM-TIM ..................................... 283
PM ....................................................... 281
SAPI ODU-TIM...................................... 283
SAPI OTU-TIM ...................................... 283
SAPI TCM-TIM ...................................... 283
SM ....................................................... 281
TCM..................................................... 281

TTL .................................... 182, 225, 502, 521
TU ............................................................. 339
TU Path ..................................................... 261
TU Path (N1).............................................. 285
TU Path (V5) ...................................... 169, 357
TU Path (Z6 or N1 (TU-3)) .................. 285, 445
TU-AIS ....................................................... 339
TU-LOP ...................................................... 339
Two-step ........................................... 114, 399
TX button.......................................... 487, 558
TX CCM ..................................................... 431
TX CIR........................................................ 412
TX DMM.................................................... 381
TX Enable .................................................. 226
TX Frames.................................................. 425
TX Frequency..................................... 156, 244
TX LBM...................................................... 379
TX LMM..................................................... 382
TX LTM ...................................................... 521
TX Mode.................................................... 270
TX Pattern ................................................. 118
TX Pattern/RX Pattern................................ 129
TX Poniter Adjustment .............................. 506
TX Power........................................... 155, 241
TX Rate.............. 133, 227, 264, 271, 385, 390
TX SLM ...................................................... 383
TX to RX .................................................... 206
TX TST ....................................................... 380
Type .................................. 164, 177, 190, 346
Type Of Service.......................................... 182

U

UA............................................................. 352
UAS ........................................... 368, 371, 418

UDP ................................................... 184, 262
UDP Checksum .......................................... 313
UDP/TCP..................................................... 538
UI............................................................... 353
Unassigned........................................ 462, 469
Undersize........................................... 308, 310
UNEQ-P.............................................. 332, 343
UNEQ-V ............................................. 169, 340
Unexp MEP ................................................ 327
Unexp Period ............................................. 327
Unexp. MD Lvl ........................................... 326
Unexp. MEG Lvl ......................................... 326
Unframed .......................................... 106, 110
Unframed (Interop) ................................... 106
Unframed BERT.................................. 117, 129
Unframed with Sync .................................. 106
Unicast ...................................................... 447
Unidirectional ............................................ 359
Unit ........................................................... 426
Unusable ................................................... 324
Use Stream ................................................ 501
User Defined Codes ................................... 183
User Performance ...................................... 197

V

V5.............................................................. 498
Val. ............................................................ 425
Valid Event Count...................................... 465
Validations ................................................ 210
Value ......................................................... 506

Filter..................................................... 473

Variable Retrieval....................................... 359
Vendor Specific Information...................... 359
Verdict......................................................... 32

-- ............................................................ 32
FAIL................................................ 32, 291
PASS .............................................. 32, 291

Version 1 ................................................... 151
Version 2 ................................................... 151
VID ............................................................ 639
Video......................................................... 267

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands