Home
/
EXFO
/
FTB-1
/
User Manual

EXFO FTB-1, User Manual

Share

Page: 145 / 675

EXFO FTB-1 User Manual Download Page 145

Test Setup - Test Configurator, Timer, and System

NetBlazer

133

EtherBERT, FC BERT, BERT (CPRI), and Unframed BERT

Shaping



TX Rate

allows the selection of the transmission rate in percentage of

utilization (100 percent by default), Mbit/s, Gbit/s, Frame/s, or IFG for
Ethernet; Mbit/s, Gbit/s, MB/s, or % for Fibre Channel. For Ethernet, the
maximum percentage is 105 percent

depending on the frame size

selected.



Enable TX

check box is automatically selected when starting the test

allowing stream generation; automatically cleared when the test stops.
The

Enable TX

check box may also be selected or cleared while the

test is running. Not available for FC BERT.

«
...
143
144
145
146
147
...
»

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands