manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 121

Test Setup - Test Configurator, Timer, and System

NetBlazer

109

Modify Structure Button

For Fibre Channel Test Application 

Interface/Rate

: Select the desired interface rate. Choices depend on 

the rates available on the NetBlazer. 

Connector

: Allows the selection of the NetBlazer’s port available for 

the selected interface/rate. 

Interface/Rate

Model

1X
2X
4X

FTB-860, FTB-860G,
FTB-720G, FTB-720G+,
FTB-730G, FTB-730G+,
FTB-870, FTB-880

8X
10X

FTB-860G, 
FTB-720G+, FTB-730G+, 
FTB-870, FTB-880

Interface/Rate

Connector

1X
2X
4X

Port 1 - SFP
Port 2 - SFP

8X
10X

Port 1 - SFP+

 

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands