manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 312

Test Results

300

FTB-700G/800 Series

Alarms/Errors

DS1 

Alarms

AIS

 (Alarm Indication Signal) 

RX

: An unframed all-ones signal is received.

OOF

 (Out-OF-Frame) 

RX

: Four consecutive frame bit errors are detected.

RAI 

(Yellow) (Remote Alarm Indication) 

RX

: 

SF framing: Bit 2 in each timeslot contains “0”.

ESF framing: Eight “ones” followed by eight “zeros” pattern is 
received continuously in the data link (FDL).

Errors

Framing Bit

 

RX

: An incorrect value appeared in a bit position reserved for framing. 

CRC-6 

(Cyclical Redundancy Check) is only available with ESF 

framing. 

RX

: One or more bit errors have been detected in a block of data 

through cyclical redundancy check. 

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands