manualshive.com logo in svg

EXFO FTB-1, User Manual

Share
Download
EXFO FTB-1 User Manual Download Page 358

Test Results

346

FTB-700G/800 Series

Alarms/Errors

Inject Button 

Layer

: Allows to select on which layer is the alarm/error to be 

generated. Choices depend on the test application and its interface. 

Type

: Allows to select the type of injection, either 

Alarms

 or 

Errors

. 

Defect

: Allows the selection of the alarm/error defect to be generated. 

Choices depend on the selected 

Layer

 and 

Type

. Refer to 

Alarms/Errors

 on page 292 for more information. 

Mode

 and 

Rate/Amount 

Manual

 allows to enter the amount of manual error to be 

generated: 

1

 (default) through 

50

 or 

100

 (depends on the selected 

error). 

Rate 

allows the selection of the injection rate for the selected error. 

The rate must be within the minimum and maximum values 
specified. 

Max Rate 

generates the selected error to its theoretical maximum 

rate. 

Open/Close pop-up button

Selected Alarm/Error

and status

Summary of Contents for FTB-1




































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands