8
8
8-246
8-246
Service Mode > SORTER > ADJUST
Service Mode > SORTER > ADJUST
SORTER > ADJUST
FIN-NIS
Set tray drive noise reduct mode: Fin-C1
Lv.1 Details
Set 1 when the Finisher operation noise is loud.
When 1 is set, the initial Finisher operation is minimized.
Use case
When the Finisher operation noise is loud
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range
0 to 1
0: OFF, 1: ON
Default value
0
1SHT-SHF
Set 1-sheet Collate: Fin-C1
Lv.1 Details
Set 1 when enabling Offset and Collate for 1-sheet document.
Use case
When enabling Offset and Collate for 1-sheet document
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range
0 to 1
0: OFF, 1: ON
Default value
0
SDL-SWCH
Sddl stack capacity switch mode:Fin-C1
Lv.1 Details
Set 1 when increasing the stacking capacity for saddle stitching.
When 1 is set, the stacking capacity increases over the upper limit.
Use case
When increasing the stacking capacity for perfect binding
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range
0 to 1
0: OFF, 1: ON
Default value
0
SDL-ALM
Set sddl full stack alarm mode: Fin-C1
Lv.1 Details
Set 1 when disabling the stack full alarm for saddle stitching.
Use case
When disabling the stack full alarm for saddle stitching
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range
0 to 1
0: ON, 1: OFF
Default value
0
SFT-AMT1
Adj Shift Roller front shft amnt: Fin-A1
Lv.1 Details
To adjust the front shift amount of the Shift Roller.
As the value is incremented by 1, the Shift Roller moves to the push-
on direction by 0.1mm.
Use case
When the front shift amount of paper is not appropriate
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range
-50 to 50
Unit
mm
Default value
0
SORTER > ADJUST
SFT-AMT2
Adj Shift Roller rear shft amnt: Fin-A1
Lv.1 Details
To adjust the rear shift amount of the Shift Roller.
As the value is incremented by 1, the Shift Roller moves to the push-
on direction by 0.1mm.
Use case
When the rear shift amount of paper is not appropriate
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range
-50 to 50
Unit
mm
Default value
0
STP-NTN
Adjustment of A4 staple pitch: Fin-A1
Lv.1 Details
To adjust the staple pitch for 2-point stapling.
As the value is incremented by 1, staple pitch is widened by 0.27mm.
Use case
When staple pitch for 2-point stapling is not appropriate
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range
-8 to 8
Unit
mm
Default value
0
INSTP-F1
Adj of front staple position: Fin-A1
Lv.1 Details
To adjust the paper pull-in amount of the Gripper at the time of front
1-point stapling.
As the value is incremented by 1, the paper pull-in amount is
increased by 0.1mm.
Use case
When the paper front staple position is displaced
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range
-50 to 50
Unit
mm
Default value
0
INSTP-R1
Adj of rear staple position: Fin-A1
Lv.1 Details
To adjust the paper pull-in amount of the Gripper at the time of rear
1-point stapling.
As the value is incremented by 1, the paper pull-in amount is
increased by 0.1mm.
Use case
When the paper rear staple position is displaced
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range
-50 to 50
Unit
mm
Default value
0