8
8
8-196
8-196
Service Mode > COPIER > OPTION > USER
Service Mode > COPIER > OPTION > USER
COPIER > OPTION > USER
DPT-ID-7
Password entry set at dept ID reg/auth
Lv.2 Details
To set whether to enter a password at the time of registration/
authentication of department ID.
With the setting to require entry, entry of 7-digit password is required
beside department ID.
Use case
Upon user’s request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Department ID only, 1: 7-digit (password) entry
Default value
0
RUI-RJT
Connct set at invalid auth from remoteUI
Lv.2 Details
To set whether to disconnect HTTP port when the machine receives
invalid authentication from remote UI 3 times.
Use case
Upon user’s request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Continued connection, 1: Disconnected
Default value
0
SND-RATE
Set compress ratio at SEND high compress
Lv.2 Details
To set the compression ratio when the data compression ratio for SEND
(transmission) is set to “Compact”.
As the value is larger, the compression ratio is higher (the file size
becomes small).
Use case
When making the transmission file size smaller
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution
As the value is too large, an image is deteriorated.
Display/adj/set range 0 to 2
0: Compression ratio 1/16, 1: Compression ratio 1/20, 2: Compression
ratio 1/24
Default value
0
FREG-SW
Dspl/hide of MEAP counter free rgst area
Lv.2 Details
To set whether to display or hide the free register area of MEAP counter
for SEND.
Use case
At problem analysis
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution
- Do not use this at the normal service.
- Take necessary action in accordance with the instructions from the
Quality Support Division.
Display/adj/set range 0 to 1
0: Hide, 1: Display
Default value
0
COPIER > OPTION > USER
IFAX-SZL
Setting of IFAX send size limit
Lv.2 Details
To set for restricting data size at the time of IFAX transmission that does
not go through the server.
With the setting to restrict the data size, it is to be #830 error in the case
of sending data that exceeds the upper limit value.
In the case that the data goes through the server, the size of
transmission data is always restricted.
Use case
Upon user’s request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Limited, 1: Unlimited (Restriction applies when data goes through the
server.)
Default value
1
IFAX-PGD
Set page split TX at IFax Simple mode TX
Lv.2 Details
To set whether to allow split-data transmission on a page basis in the
case that the transmission size in I-Fax Simple mode exceeds the upper
limit value.
Use case
Upon user’s request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution
In the case to enable split-data transmission, be sure to receive approval
from the user in advance by explaining the following:
- No guarantee for page order on the reception side
- There is a possibility of interruption of other received jobs between
pages.
Display/adj/set range 0 to1
0: Disabled, 1: Enabled
Default value
0
MEAPSAFE
Setting of MEAP safe mode
Lv.2 Details
To set safe mode for MEAP platform.
MPSF is displayed on the Control Panel in safe mode.
In safe mode, MEAP application is stopped while just the system
application, which starts with initial state, is activated. This mode
enables obtaining log for cause analysis of MEAP failure.
Use case
Perform system recovery processing when MEAP platform fails to be
activated due to resource conflict between MEAP applications, service
registration or use order.
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Normal mode, 1: Safe mode
Default value
0