manualshive.com logo in svg

Texas Instruments TMS320 2806 Series, Техническое справочное руководство


Поделиться
Скачать
background image

Table 15-31. Register Bits Used to Set the Receive Data Delay (continued)

Register

Bit

Name

Function

Type

Reset 

Value

RDATDLY = 11

Reserved

15.7.12.1 Data Delay

The start of a frame is defined by the first clock cycle in which frame synchronization is found to be active. 
The beginning of actual data reception or transmission with respect to the start of the frame can be delayed if 
required. This delay is called data delay.

RDATDLY specifies the data delay for reception. The range of programmable data delay is zero to two bit-
clocks (RDATDLY = 00b-10b), as described in 

Table 15-31

 and shown in 

Figure 15-46

. In this figure, the data 

transferred is an 8-bit value with bits labeled B7, B6, B5, and so on. Typically a 1-bit delay is selected, because 
data often follows a 1-cycle active frame-synchronization pulse.

15.7.12.2 0-Bit Data Delay

Normally, a frame-synchronization pulse is detected or sampled with respect to an edge of internal serial clock 
CLK(R/X). Thus, on the following cycle or later (depending on the data delay value), data may be received or 
transmitted. However, in the case of 0-bit data delay, the data must be ready for reception and/or transmission 
on the same serial clock cycle.

For reception, this problem is solved because receive data is sampled on the first falling edge of MCLKR where 
an active-high internal FSR is detected. However, data transmission must begin on the rising edge of the internal 
CLKX clock that generated the frame synchronization. Therefore, the first data bit is assumed to be present in 
XSR1, and thus on DX. The transmitter then asynchronously detects the frame-synchronization signal (FSX) 
going active high and immediately starts driving the first bit to be transmitted on the DX pin.

B5

B6

B7

B4

B5

B6

B7

B3

B4

B5

B6

B7

Data delay 2

D(R/X)

Data delay 1

D(R/X)

Data delay 0

D(R/X)

FS(R/X)

CLK(R/X)

1-bit delay

Á

Á

Á

Á

ÁÁ

ÁÁ

ÁÁ

ÁÁ

Á

Á

Á

Á

0-bit delay

2-bit delay

Figure 15-46. Range of Programmable Data Delay

15.7.12.3 2-Bit Data Delay

A data delay of two bit periods allows the serial port to interface to different types of T1 framing devices where 
the data stream is preceded by a framing bit. During reception of such a stream with data delay of two bits 
(framing bit appears after a 1-bit delay and data appears after a 2-bit delay), the serial port essentially discards 
the framing bit from the data stream, as shown in 

Figure 15-47

. In this figure, the data transferred is an 8-bit 

value with bits labeled B7, B6, B5, and so on.

www.ti.com

Multichannel Buffered Serial Port (McBSP)

SPRUH18I – JANUARY 2011 – REVISED JUNE 2022

Submit Document Feedback

TMS320x2806x Microcontrollers

927

Copyright © 2022 Texas Instruments Incorporated

Содержание TMS320 2806 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320 2806 Series

Desoutter 6159326760 Original Instructions Manual preview
6159326760
Бренд: Desoutter Страницы: 74
Sentiotec CV 4 Installation And Operating Instructions Manual preview
CV 4
Бренд: Sentiotec Страницы: 45
Z-Wave HKZW-STICK Operating Manual preview
HKZW-STICK
Бренд: Z-Wave Страницы: 3
Wittenstein TPM dynamic Operating Manual preview
TPM dynamic
Бренд: Wittenstein Страницы: 52
Black Stone BL 981411-0 Instruction Manual preview
BL 981411-0
Бренд: Black Stone Страницы: 2
Mita WP3000 Manual preview
WP3000
Бренд: Mita Страницы: 7
SystemAir fantech IPF05-1L Installation Instructions preview
fantech IPF05-1L
Бренд: SystemAir Страницы: 2
Samson 46-5 Mounting And Operating Instructions preview
46-5
Бренд: Samson Страницы: 24
YOKOGAWA UT32A-C Operation Manual preview
UT32A-C
Бренд: YOKOGAWA Страницы: 10
ICP DAS USA CAN-8124 User Manual preview
CAN-8124
Бренд: ICP DAS USA Страницы: 153
Bardac PLX Product Manual preview
PLX
Бренд: Bardac Страницы: 235
Kilews SKP-BC32HL Operation And Maintenance Manual preview
SKP-BC32HL
Бренд: Kilews Страницы: 26
OptoSupply OS-OC013AIG2 Product Manual preview
OS-OC013AIG2
Бренд: OptoSupply Страницы: 4
Smartgen HEM4000 User Manual preview
HEM4000
Бренд: Smartgen Страницы: 46
MDT AKI-0416.01 Manual preview
AKI-0416.01
Бренд: MDT Страницы: 39
Häfele WT 210 BLE Operating Instructions Manual preview
WT 210 BLE
Бренд: Häfele Страницы: 76
Proton ECOMATIC PRO ECP 220 Operation Manual preview
ECOMATIC PRO ECP 220
Бренд: Proton Страницы: 36
NEC V850E/PH2 User Manual preview
V850E/PH2
Бренд: NEC Страницы: 1053

Бренды по названию

Популярные бренды

Загрузить еще бренды