manualshive.com logo in svg

Texas Instruments TMS320 2806 Series, Техническое справочное руководство


Поделиться
Скачать
background image

Table 15-78. SPCR1 Register Field Descriptions (continued)

Bit

Field

Type

Reset

Description

12-11

CLKSTP

R/W

0h

Clock stop mode bits.
CLKSTP allows you to use the clock stop mode to support the SPI 
master/slave protocol. If you will not be using the SPI protocol, you 
can clear CLKSTP to disable the clock stop mode.
In the clock stop mode, the clock stops at the end of each data 
transfer. At the beginning of each data transfer, the clock starts 
immediately (CLKSTP = 10b) or after a half-cycle delay (CLKSTP 
= 11b).
Reset type: SYSRSn
0h (R/W) = Clock stop mode is disabled.
1h (R/W) = Clock stop mode is disabled.
2h (R/W) = Clock stop mode, without clock delay
3h (R/W) = Clock stop mode, with half-cycle clock delay

10-8

RESERVED

R

0h

Reserved

7

DXENA

R/W

0h

DX delay enabler mode bit.
DXENA controls the delay enabler for the DX pin. The enabler 
creates an extra delay for turn-on time (for the length of the delay, 
see the device-specific data sheet).
Reset type: SYSRSn
0h (R/W) = DX delay enabler off
1h (R/W) = DX delay enabler on

6

RESERVED

R/W

0h

Reserved

5-4

RINTM

R/W

0h

Receive interrupt mode bits.
RINTM determines which event in the McBSP receiver generates a 
receive interrupt (RINT) request. If RINT is properly enabled inside 
the CPU, the CPU services the interrupt request
otherwise, the CPU ignores the request.
Reset type: SYSRSn
0h (R/W) = The McBSP sends a receive interrupt (RINT) request to 
the CPU when the RRDY bit changes from 0 to 1, indicating that 
receive data is ready to be read (the content of RBR[1,2] has been 
copied to DRR[1,2]):
Regardless of the value of RINTM, you can check RRDY to 
determine whether a word transfer is complete.
The McBSP sends a RINT request to the CPU when 16 enabled bits 
have been received on the DR pin.
1h (R/W) = In the multichannel selection mode, the McBSP sends a 
RINT request to the CPU after every 16- channel block is received in 
a frame.
Outside of the multichannel selection mode, no interrupt request is 
sent.
2h (R/W) = The McBSP sends a RINT request to the CPU when 
each receive frame-synchronization pulse is detected. The interrupt 
request is sent even if the receiver is in its reset state.
3h (R/W) = The McBSP sends a RINT request to the CPU when 
the RSYNCERR bit is set, indicating a receive frame-synchronization 
error.
Regardless of the value of RINTM, you can check RSYNCERR to 
determine whether a receive frame-synchronization error occurred.

www.ti.com

Multichannel Buffered Serial Port (McBSP)

SPRUH18I – JANUARY 2011 – REVISED JUNE 2022

Submit Document Feedback

TMS320x2806x Microcontrollers

967

Copyright © 2022 Texas Instruments Incorporated

Содержание TMS320 2806 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320 2806 Series

ZKTeco SC800 User Manual preview
SC800
Бренд: ZKTeco Страницы: 123
Canon imageRUNNER ADVANCE C9075S PRO User Manual preview
imageRUNNER ADVANCE C9075S PRO
Бренд: Canon Страницы: 20
Panasonic Minas A4 Series Connection Manual preview
Minas A4 Series
Бренд: Panasonic Страницы: 5
Galcon 6100 Series Installation And Operating Instructions Manual preview
6100 Series
Бренд: Galcon Страницы: 32
Datapath HX4 Quick Start Manual preview
HX4
Бренд: Datapath Страницы: 12
L-Acoustics LA8 Product Information preview
LA8
Бренд: L-Acoustics Страницы: 20
WINDY NATION CHC-LCD-30FM User Manual preview
CHC-LCD-30FM
Бренд: WINDY NATION Страницы: 16
Ros IC-15X Operation And Maintenance Manual preview
IC-15X
Бренд: Ros Страницы: 10
Atari IDEa How To Connect preview
IDEa
Бренд: Atari Страницы: 3
Woodward ProAct III Installation And Operation Manual preview
ProAct III
Бренд: Woodward Страницы: 32
NXP Semiconductors AN10815 Application Note preview
AN10815
Бренд: NXP Semiconductors Страницы: 20
Swagelok BSH 10 Series User Manual preview
BSH 10 Series
Бренд: Swagelok Страницы: 20
Kramer FC-21ETH User Manual preview
FC-21ETH
Бренд: Kramer Страницы: 60
Kelly KLS4812S User Manual preview
KLS4812S
Бренд: Kelly Страницы: 32
Srne ML4860N15 User Manual preview
ML4860N15
Бренд: Srne Страницы: 13
NEC mPD789101 User Manual preview
mPD789101
Бренд: NEC Страницы: 265
National Instruments PXI-8232 Installation Manual preview
PXI-8232
Бренд: National Instruments Страницы: 8
TIE AMBITECH BRAKE-PAK Installation & Setup Instructions preview
AMBITECH BRAKE-PAK
Бренд: TIE Страницы: 5

Бренды по названию

Популярные бренды

Загрузить еще бренды