manualshive.com logo in svg

Texas Instruments TMS320 2806 Series, Техническое справочное руководство


Поделиться
Скачать
background image

10.3 CLA and CPU Arbitration

Typically, CLA activity is independent of the CPU activity. Under the circumstance where the CLA or CPU 
attempt to concurrently access memory or a peripheral register within the same interface, an arbitration 
procedure will occur. This section describes this arbitration.

The arbitration follows a fixed arbitration scheme with highest priority first:

They are covered in detail in the Memory Controller Module section of the 

System Control and Interrupts 

chapter.

10.3.1 CLA Message RAM

Message RAMs consist of blocks:

• CLA to CPU Message RAM
• CPU to CLA Message RAM

These blocks are useful for passing data between the CLA and CPU. No opcode fetches, from either the CLA 
or CPU, are allowed from the message RAMs. A write protection violation is not generated if the CLA attempts 
to write to the CPU to CLA message RAM, but the write is ignored. The arbitration scheme for the message 
RAMs are the same as those for the shared memories, described in the Memory Controller Module section of 
the 

System Control and Interrupts

 chapter.

The message RAMs have the following characteristics:

• CLA to CPU Message RAM:

The following accesses are allowed:
– CPU reads
– CLA data reads and writes
– CPU debug reads and writes

The following accesses are ignored:
– CPU writes

• CPU to CLA Message RAM:

The following accesses are allowed:
– CPU reads and writes
– CLA reads
– CPU debug reads and writes

The following accesses are ignored:
– CLA writes

www.ti.com

Control Law Accelerator (CLA)

SPRUH18I – JANUARY 2011 – REVISED JUNE 2022

Submit Document Feedback

TMS320x2806x Microcontrollers

575

Copyright © 2022 Texas Instruments Incorporated

Содержание TMS320 2806 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320 2806 Series

UniKey SR3 Installation Manual & User Manual preview
SR3
Бренд: UniKey Страницы: 20
vacuubrand CVC 3000 Instructions For Assembly preview
CVC 3000
Бренд: vacuubrand Страницы: 12
Vacon 100 INDUSTRIAL Installation And User Manual preview
100 INDUSTRIAL
Бренд: Vacon Страницы: 47
Vacon 100 flow Installation Instruction preview
100 flow
Бренд: Vacon Страницы: 40
G&D PersonalWorkplace Pro Video Installation Manual preview
PersonalWorkplace Pro Video
Бренд: G&D Страницы: 56
Sonos Controller CR100 Brochure & Specs preview
Controller CR100
Бренд: Sonos Страницы: 2
ASROCK iEP-5000G Series Quick Installation Manual preview
iEP-5000G Series
Бренд: ASROCK Страницы: 2
NXP Semiconductors Freescale Xtrinsic LFSTBEB865X Quick Start Manual preview
Freescale Xtrinsic LFSTBEB865X
Бренд: NXP Semiconductors Страницы: 2
Topcon OPUS A3 Eco Get Started preview
OPUS A3 Eco
Бренд: Topcon Страницы: 9
Walchem WDIS Series Instruction Manual preview
WDIS Series
Бренд: Walchem Страницы: 35
AL-KO UP4 Translation Of The Original Installation Instructions preview
UP4
Бренд: AL-KO Страницы: 52
Belimo SM24A-S Technical Data Sheet preview
SM24A-S
Бренд: Belimo Страницы: 4
G-Scale Graphics LSCM2 Operation And Installation Manual preview
LSCM2
Бренд: G-Scale Graphics Страницы: 7
Madas RG/2MBLZ DN 80 Technical Manual preview
RG/2MBLZ DN 80
Бренд: Madas Страницы: 48
Ledj STAR11 User Manual preview
STAR11
Бренд: Ledj Страницы: 12
Hanbay MC DC-2.00 Series User Manual preview
MC DC-2.00 Series
Бренд: Hanbay Страницы: 7
TA DA 516 Manual preview
DA 516
Бренд: TA Страницы: 8
Flycolor Raptor S-Tower F4-20A User Manual preview
Raptor S-Tower F4-20A
Бренд: Flycolor Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды