manualshive.com logo in svg

Texas Instruments TMS320 2806 Series, Техническое справочное руководство


Поделиться
Скачать
background image

15.7.15.1 Receive Frame-Synchronization Modes

Table 15-37

 shows how you can select various sources to provide the receive frame-synchronization signal and 

the effect on the FSR pin. The polarity of the signal on the FSR pin is determined by the FSRP bit.

In digital loopback mode (DLB = 1), the transmit frame-synchronization signal is used as the receive frame-
synchronization signal.

Also in the clock stop mode, the internal receive clock signal (MCLKR) and the internal receive frame-
synchronization signal (FSR) are internally connected to their transmit counterparts, CLKX and FSX.

Table 15-37. Select Sources to Provide the Receive Frame-Synchronization Signal and the Effect on the 

FSR Pin

DLB

FSRM

GSYNC

Source of Receive Frame
Synchronization

FSR Pin Status

0

0

0 or 1

An external frame-synchronization signal 
enters the McBSP through the FSR pin. The 
signal is then inverted as determined by 
FSRP before being used as internal FSR.

Input

0

1

0

Internal FSR is driven by the sample 
rate generator frame-synchronization signal 
(FSG).

Output. FSG is inverted as determined by 
FSRP before being driven out on the FSR 
pin.

0

1

1

Internal FSR is driven by the sample 
rate generator frame-synchronization signal 
(FSG).

Input. The external frame-synchronization 
input on the FSR pin is used to synchronize 
CLKG and generate FSG pulses.

1

0

0

Internal FSX drives internal FSR.

High impedance

1

0 or 1

1

Internal FSX drives internal FSR.

Input. If the sample rate generator is 
running, external FSR is used to synchronize 
CLKG and generate FSG pulses.

1

1

0

Internal FSX drives internal FSR.

Output. Receive (same as transmit) frame 
synchronization is inverted as determined by 
FSRP before being driven out on the FSR 
pin.

www.ti.com

Multichannel Buffered Serial Port (McBSP)

SPRUH18I – JANUARY 2011 – REVISED JUNE 2022

Submit Document Feedback

TMS320x2806x Microcontrollers

931

Copyright © 2022 Texas Instruments Incorporated

Содержание TMS320 2806 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320 2806 Series

J4C 20 Mounting Instructions preview
20
Бренд: J4C Страницы: 4
M-Audio Axiom AIR 25 Service Manual preview
Axiom AIR 25
Бренд: M-Audio Страницы: 26
M Climate Bobbie Installation Instructions Manual preview
Bobbie
Бренд: M Climate Страницы: 12
York CIW01 Installation & Maintenance Manual preview
CIW01
Бренд: York Страницы: 24
Centurion TB-CN2R1 Instruction Manual preview
TB-CN2R1
Бренд: Centurion Страницы: 16
NEC uPD78F4225Y Manual preview
uPD78F4225Y
Бренд: NEC Страницы: 30
Aqua Lung Cousteau/ SEA Service & Repair Manual preview
Cousteau/ SEA
Бренд: Aqua Lung Страницы: 24
ACTi R12CP-30 Installation Manual preview
R12CP-30
Бренд: ACTi Страницы: 20
SOARNEX EWC-100 Quick Installation Manual preview
EWC-100
Бренд: SOARNEX Страницы: 14
D+H VCD 203 Manual preview
VCD 203
Бренд: D+H Страницы: 16
CompuPro DISK 3 Technical Manual preview
DISK 3
Бренд: CompuPro Страницы: 33
SainSmart 101-40-173 Assembly preview
101-40-173
Бренд: SainSmart Страницы: 17
Aurora Scientific 315D Instruction Manual preview
315D
Бренд: Aurora Scientific Страницы: 21
Clare Controls CLIQ.host Installation Sheet preview
CLIQ.host
Бренд: Clare Controls Страницы: 3
Swegon TACTouch TAC5 Manual preview
TACTouch TAC5
Бренд: Swegon Страницы: 11
Leviton DECORA ILLUMATECH IPF01-1LX Installation Instructions preview
DECORA ILLUMATECH IPF01-1LX
Бренд: Leviton Страницы: 2
MSA SUPREMA Touch Installation & Maintenance Instructions Manual preview
SUPREMA Touch
Бренд: MSA Страницы: 309
SAES NEG POWER User Manual preview
NEG POWER
Бренд: SAES Страницы: 36

Бренды по названию

Популярные бренды

Загрузить еще бренды