manualshive.com logo in svg

Texas Instruments TMS320 2806 Series, Техническое справочное руководство


Поделиться
Скачать
background image

• Asynchronous override control of PWM signals through software.
• Programmable phase-control support for lag or lead operation relative to other ePWM modules.
• Hardware-locked (synchronized) phase relationship on a cycle-by-cycle basis.
• Dead-band generation with independent rising and falling edge delay control.
• Programmable trip zone allocation of both cycle-by-cycle trip and one-shot trip on fault conditions.
• A trip condition can force either high, low, or high-impedance state logic levels at PWM outputs.
• Comparator module outputs and trip zone inputs can generate events, filtered events, or trip conditions.
• All events can trigger both CPU interrupts and ADC start of conversion (SOC).
• Programmable event prescaling minimizes CPU overhead on interrupts.
• PWM chopping by high-frequency carrier signal, useful for pulse transformer gate drives.

Each ePWM module is connected to the input/output signals shown in 

Figure 3-1

. The signals are described in 

detail in subsequent sections.

The order in which the ePWM modules are connected may differ from what is shown in 

Figure 3-1

. See 

Section 3.2.2.3.3

 for the synchronization scheme for a particular device. Each ePWM module consists of eight 

submodules and is connected within a system with the signals shown in 

Figure 3-2

.

www.ti.com

Enhanced Pulse Width Modulator (ePWM) Module

SPRUH18I – JANUARY 2011 – REVISED JUNE 2022

Submit Document Feedback

TMS320x2806x Microcontrollers

243

Copyright © 2022 Texas Instruments Incorporated

Содержание TMS320 2806 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320 2806 Series

Camozzi PRE Series Operation And Maintenance Instructions preview
PRE Series
Бренд: Camozzi Страницы: 33
Camozzi PME Series Operation & Maintenance Instructions Manual preview
PME Series
Бренд: Camozzi Страницы: 64
SDC E4KP ENTRYCHECK Operating Instructions Manual preview
E4KP ENTRYCHECK
Бренд: SDC Страницы: 6
select solar EPHC 10A Instruction Manual preview
EPHC 10A
Бренд: select solar Страницы: 2
Kelly KLS4812S User Manual preview
KLS4812S
Бренд: Kelly Страницы: 32
Velleman CHLSC2 User Manual preview
CHLSC2
Бренд: Velleman Страницы: 22
National Instruments NI 9683 User Manual And Specifications preview
NI 9683
Бренд: National Instruments Страницы: 27
H3C WX2560H Installation, Quick Start preview
WX2560H
Бренд: H3C Страницы: 3
Wahlberg 255.700 User Manual preview
255.700
Бренд: Wahlberg Страницы: 40
Belimo CQB24-3 Instruction Manual preview
CQB24-3
Бренд: Belimo Страницы: 2
YOKOGAWA STARDOM FCN-500 Engineering Manual preview
STARDOM FCN-500
Бренд: YOKOGAWA Страницы: 226
oventrop Hydromat DP DN 20 Operating Instructions Manual preview
Hydromat DP DN 20
Бренд: oventrop Страницы: 40
NXP Semiconductors MPC560xP Design Manual preview
MPC560xP
Бренд: NXP Semiconductors Страницы: 25
Salus PCSol 150 Installation And Operation Manual preview
PCSol 150
Бренд: Salus Страницы: 24
p5 FutureNow FNIP-4xSH-12 Installation Manual preview
FutureNow FNIP-4xSH-12
Бренд: p5 Страницы: 20
Shimaden PAC46 Series Instruction Manual preview
PAC46 Series
Бренд: Shimaden Страницы: 24
ACME uPilot LED-RC64 Manual preview
uPilot LED-RC64
Бренд: ACME Страницы: 2
Power Electronics SIEMENS 6GA-2491 User Manual preview
SIEMENS 6GA-2491
Бренд: Power Electronics Страницы: 7

Бренды по названию

Популярные бренды

Загрузить еще бренды