manualshive.com logo in svg

Texas Instruments TMS320 2806 Series, Техническое справочное руководство


Поделиться
Скачать
background image

16.7.4.3.2 Handling Mailbox Interrupts

There are three interrupt flags for mailbox interrupts. These are listed below:

GMIF0/GMIF1: One of the objects has received or transmitted a message. The number of the mailbox is in 
MIV0/MIV1(GIF0.4-0/GIF1.4-0). The normal handling routine is as follows:

1. Do a half-word read on the GIF register that caused the interrupt. If the value is negative, a mailbox caused 

the interrupt. Otherwise, check the AAIF0/AAIF1 (GIF0.14/GIF1.14) bit (abort-acknowledge interrupt flag) 
or the RMLIF0/RMLIF1 (GIF0.11/GIF1.11) bit (receive-message-lost interrupt flag). Otherwise, a system 
interrupt has occurred. In this case, each of the system-interrupt flags must be checked.

2. If the RMLIF (GIF0.11) flag caused the interrupt, the message in one of the mailboxes has been overwritten 

by a new one. This should not happen in normal operation. The CPU needs to clear that flag by writing 
a 1 to it. The CPU must check the receive-message-lost register (RML) to find out which mailbox caused 
that interrupt. Depending on the application, the CPU has to decide what to do next. This interrupt comes 
together with an GMIF0/GMIF1 interrupt.

3. If the AAIF (GIF.14) flag caused the interrupt, a send transmission operation was aborted by the CPU. The 

CPU should check the abort acknowledge register (AA.31-0) to find out which mailbox caused the interrupt 
and send that message again if requested. The flag must be cleared by writing a 1 to it.

4. If the GMIF0/GMIF1 (GIF0.15/GIF1.15) flag caused the interrupt, the mailbox number that caused the 

interrupt can be read from the MIV0/MIV1 (GIF0.4-0/GIF1.4-0) field. This vector can be used to jump to a 
location where that mailbox is handled. If it is a receive mailbox, the CPU should read the data as described 
above and clear the RMP.31-0 flag by writing a 1 to it. If it is a send mailbox, no further action is required, 
unless the CPU needs to send more data. In this case, the normal send procedure as described above is 
necessary. The CPU needs to clear the transmit acknowledge bit (TA.31-0) by writing a 1 to it.

 

16.7.4.3.3 Interrupt Handling Sequence

In order for the CPU core to recognize and service CAN interrupts, the following must be done in any CAN ISR:

1. The flag bit in the CANGIF0/CANGIF1 register which caused the interrupt in the first place must be cleared. 

There are two kinds of bits in these registers:
a. the very same bit that needs to be cleared. The following bits fall under this category: TCOFn, WDIFn, 

WUIFn, BOIFn, EPIFn, WLIFn

b. The second group of bits are cleared by writing to the corresponding bits in the associated registers. The 

following bits fall under this category: MTOFn, GMIFn, AAIFn, RMLIFn
i.

The MTOFn bit is cleared by clearing the corresponding bit in the TOS register. For example, if 
mailbox 27 caused a time-out condition due to which the MTOFn bit was set, the ISR (after taking 
appropriate actions for the timeout condition) needs to clear the TOS27 bit in order to clear the 
MTOFn bit.

ii. The GMIFn bit is cleared by clearing the appropriate bit in TA or RMP register. For example, if 

mailbox 19 has been configured as a transmit mailbox and has completed a transmission, TA19 is 
set, which in turn sets GMIFn. The ISR (after taking appropriate actions) needs to clear the TA19 
bit in order to clear the GMIFn bit. If mailbox 8 has been configured as a receive mailbox and has 
completed a reception, RMP8 is set, which in turn sets GMIFn. The ISR (after taking appropriate 
actions) needs to clear the RMP8 bit in order to clear the GMIFn bit.

iii. The AAIFn bit is cleared by clearing the corresponding bit in the AA register. For example, if mailbox 

13’s transmission was aborted due to which the AAIFn bit was set, the ISR needs to clear the AA13 
bit in order to clear the AAIFn bit.

iv. The RMLIFn bit is cleared by clearing the corresponding bit in the RMP register. For example, if 

mailbox 13’s message was overwritten due to which the RMLIFn bit was set, the ISR needs to clear 
the RMP13 bit in order to clear the RMLIFn bit.

www.ti.com

Controller Area Network (CAN)

SPRUH18I – JANUARY 2011 – REVISED JUNE 2022

Submit Document Feedback

TMS320x2806x Microcontrollers

1021

Copyright © 2022 Texas Instruments Incorporated

Содержание TMS320 2806 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320 2806 Series

Lattice Semiconductor CrossLink Programming And Configuration Manual preview
CrossLink
Бренд: Lattice Semiconductor Страницы: 30
Paoli F1 Operating And Maintenance Manual preview
F1
Бренд: Paoli Страницы: 16
Calpeda IDROMAT 5 Quick Start Manual preview
IDROMAT 5
Бренд: Calpeda Страницы: 4
Federal Signal Corporation ultravoice UV Installation, Operation And Service Manual preview
ultravoice UV
Бренд: Federal Signal Corporation Страницы: 79
Federal Signal Corporation PAGASYS GEN II Description, Installation, And User Manual preview
PAGASYS GEN II
Бренд: Federal Signal Corporation Страницы: 32
LANGER EMV-Technik E 1 User Manual preview
E 1
Бренд: LANGER EMV-Technik Страницы: 48
Lattice Semiconductor MachXO5-NX Development Kit Quick Start preview
MachXO5-NX Development Kit
Бренд: Lattice Semiconductor Страницы: 2
KaMo Pearldex Series Manual preview
Pearldex Series
Бренд: KaMo Страницы: 2
Danfoss AFD 2 VFG 2 Operating Manual preview
AFD 2 VFG 2
Бренд: Danfoss Страницы: 8
Acuity Controls nLight ECLYPSE Safety Instructions preview
nLight ECLYPSE
Бренд: Acuity Controls Страницы: 5
Bard CompleteStat-Series CS9B-THO Product Manual preview
CompleteStat-Series CS9B-THO
Бренд: Bard Страницы: 2
Cardin Elettronica S486 Series Installation And Reference preview
S486 Series
Бренд: Cardin Elettronica Страницы: 56
e-survey P8II Quick Start Manual preview
P8II
Бренд: e-survey Страницы: 12
Pegasus Astro Dual Motor Focus Controller Manual preview
Dual Motor Focus Controller
Бренд: Pegasus Astro Страницы: 16
Kohzu Precision RC-010 Manual preview
RC-010
Бренд: Kohzu Precision Страницы: 58
Nuvation BMS NUV100-CI-12 Installation Manual preview
BMS NUV100-CI-12
Бренд: Nuvation Страницы: 41
National Instruments NI cRIO-9053 User Manual preview
NI cRIO-9053
Бренд: National Instruments Страницы: 100
YOKOGAWA Revolution FA-M3 R Technical Information preview
Revolution FA-M3 R
Бренд: YOKOGAWA Страницы: 57

Бренды по названию

Популярные бренды

Загрузить еще бренды