manualshive.com logo in svg

Texas Instruments TMS320 2806 Series, Техническое справочное руководство


Поделиться
Скачать
background image

10.4.2 Typical CLA Initialization Sequence

A typical CLA initialization sequence is performed by the main CPU as described in this section.

1.

Copy CLA code into the CLA program RAM

The source for the CLA code can initially reside in the Flash or a data stream from a communications 
peripheral or anywhere the main CPU can access it. The debugger can also be used to load code directly to 
the CLA program RAM during development.

2.

Initialize CLA data RAM, if necessary

Populate the CLA data RAM with any required data coefficients or constants.

3.

Configure the CLA registers

Configure the CLA registers, but keep interrupts disabled until later (leave MIER = 0):
•

Enable the CLA peripheral clock using the assigned PCLKCRn register

The peripheral clock control (PCLKCRn) registers are defined in the 

System Control and Interrupts 

chapter.

•

Populate the CLA task interrupt vectors 

– MVECT1 to MVECT8

Each vector needs to be initialized with the start address of the task to be executed when the CLA 
receives the associated interrupt. The address is an offset from the base address of the assigned CLA 
Program memory block.

•

Select the task interrupt sources

For each task select the interrupt source in the CLA1TASKSRCSELx register. If a task is software 
triggered, select no interrupt.

•

Enable IACK to start a task from software, if desired

To enable the IACK instruction to start a task set the MCTL[IACKE] bit. Using the IACK instruction avoids 
having to set and clear the EALLOW bit.

•

Map CLA data RAM to CLA space, if necessary

Map the data RAM to the CLA space by writing a 1 to the MMEMCFG[RAMxE] bit. The CPU will have 
restricted access to the memory block once the MMEMCFG[RAMxE] bit is set. CPU access to CLA data 
RAM can be granted through the MMEMCFG[RAMxCPUE] bit. Allow two SYSCLK cycles for MMEMCFG 
updates to take effect.

•

Map CLA program RAM to CLA space

Map the CLA program RAM to CLA space by setting the MMEMCFG[PROGE] bit. The CPU will only 
have debug access to program RAM once the MMEMCFG[PROGE] bit is set. Allow two SYSCLK cycles 
for MMEMCFG updates to take effect.

www.ti.com

Control Law Accelerator (CLA)

SPRUH18I – JANUARY 2011 – REVISED JUNE 2022

Submit Document Feedback

TMS320x2806x Microcontrollers

579

Copyright © 2022 Texas Instruments Incorporated

Содержание TMS320 2806 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320 2806 Series

Aalborg DPC Operating Manual preview
DPC
Бренд: Aalborg Страницы: 128
NEC 78K0S/KA1+ Preliminary User'S Manual preview
78K0S/KA1+
Бренд: NEC Страницы: 304
Balmar Max Charge MC-624 Installation And Operator'S Manual preview
Max Charge MC-624
Бренд: Balmar Страницы: 8
Balmar MAX CHARGE MC-614 Installation And Operation Manual preview
MAX CHARGE MC-614
Бренд: Balmar Страницы: 20
Raypak RayTemp Installation & Operating Instructions Manual preview
RayTemp
Бренд: Raypak Страницы: 24
J+J S 20 Handbook preview
S 20
Бренд: J+J Страницы: 91
YOKOGAWA TC 10-L Engineering Manual preview
TC 10-L
Бренд: YOKOGAWA Страницы: 20
YOKOGAWA UTAdvanced UT32A Technical Information preview
UTAdvanced UT32A
Бренд: YOKOGAWA Страницы: 3
Cypress CY8C28 series Technical Reference Manual preview
CY8C28 series
Бренд: Cypress Страницы: 571
Timotion TBB5 User Manual preview
TBB5
Бренд: Timotion Страницы: 9
DIG 410BT Series Instruction Manual preview
410BT Series
Бренд: DIG Страницы: 16
THOR THPWM-30 Instruction Manual preview
THPWM-30
Бренд: THOR Страницы: 12
VADDIO HOT-SHOT Installation And User Manual preview
HOT-SHOT
Бренд: VADDIO Страницы: 16
A-T Controls Triad Controls WE Series Installation And Operation Manual preview
Triad Controls WE Series
Бренд: A-T Controls Страницы: 13
Texas Instruments TDP0604 User Manual preview
TDP0604
Бренд: Texas Instruments Страницы: 19
Zamel exta life SRM-22 Operation Manual preview
exta life SRM-22
Бренд: Zamel Страницы: 5
YASKAWA MP3100 Series Instructions Manual preview
MP3100 Series
Бренд: YASKAWA Страницы: 25
Edge-Core EWS5203 Regulatory Information preview
EWS5203
Бренд: Edge-Core Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды