manualshive.com logo in svg

Texas Instruments TMS320 2806 Series, Техническое справочное руководство


Поделиться
Скачать
background image

1.3.4.5 Watchdog Registers

The system control and status register (SCSR) contains the watchdog override bit and the watchdog interrupt 
enable/disable bit. 

Figure 1-45

 describes the bit functions of the SCSR register.

Figure 1-45. System Control and Status Register (SCSR)

15

8

Reserved

R-0

7

3

2

1

0

Reserved

WDINTS

WDENINT

WDOVERRIDE

R-0

R-1

R/W-0

R/W1C-1

LEGEND: R/W = Read/Write; R = Read only; -

n

 = value after reset

Table 1-43. System Control and Status Register (SCSR) Field Descriptions

Bit

Field

Value

Description 

(1)

15-3

Reserved

Any writes to these bits must always have a value of 0.

2

WDINTS

Watchdog interrupt status bit. WDINTS reflects the current state of the WDINT signal from the 
watchdog block. WDINTS follows the state of WDINT by two SYSCLKOUT cycles.

If the watchdog interrupt is used to wake the device from IDLE or STANDBY low power mode, use 
this bit to make sure WDINT is not active before attempting to go back into IDLE or STANDBY 
mode.

0

Watchdog interrupt signal ( WDINT) is active.

1

Watchdog interrupt signal ( WDINT) is not active.

1

WDENINT

Watchdog interrupt enable.

0

The watchdog reset ( WDRST) output signal is enabled and the watchdog interrupt ( WDINT) 
output signal is disabled. This is the default state on reset ( XRS). When the watchdog interrupt 
occurs the WDRST signal will stay low for 512 OSCCLK cycles.

If the WDENINT bit is cleared while WDINT is low, a reset will immediately occur. The WDINTS bit 
can be read to determine the state of the WDINT signal.

1

The WDRST output signal is disabled and the WDINT output signal is enabled. When the watchdog 
interrupt occurs, the WDINTsignal will stay low for 512 OSCCLK cycles.

If the watchdog interrupt is used to wake the device from IDLE or STANDBY low power mode, 
use the WDINTS bit to make sure WDINT is not active before attempting to go back into IDLE or 
STANDBY mode.

0

WDOVERRIDE

Watchdog override - Protects the watchdog from being disabled by the watchdog disable (WDDIS) 
bit in the watchdog control (WDCR) register.

0

WDDIS in WDCR has no effect and WD cannot be disabled.  If this bit is cleared, it remains in this 
state until a reset occurs.

1

WDDIS bit in WDCR can disable the watchdog. This bit is a clear-only bit (write 1 to clear).  The 
reset default of this bit is a 1, and writing a 1 clears this bit (bit becomes 0) and the WD cannot be 
disabled.  Writing a 0 has no effect.

(1)

This register is EALLOW protected. See 

Section 1.5.2

 for more information.

www.ti.com

System Control and Interrupts

SPRUH18I – JANUARY 2011 – REVISED JUNE 2022

Submit Document Feedback

TMS320x2806x Microcontrollers

99

Copyright © 2022 Texas Instruments Incorporated

Содержание TMS320 2806 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320 2806 Series

Vacon 20 Quick Manual preview
20
Бренд: Vacon Страницы: 62
ABB XFC G5 Quick Start Manual preview
XFC G5
Бренд: ABB Страницы: 2
GE 400 Series Installation Instructions preview
400 Series
Бренд: GE Страницы: 2
Danfoss ERC 211 User Manual preview
ERC 211
Бренд: Danfoss Страницы: 36
Fairchild 1600A Installation, Operation And Maintenance Instructions preview
1600A
Бренд: Fairchild Страницы: 2
Fairford synergy User Manual preview
synergy
Бренд: Fairford Страницы: 233
halstrup-walcher PSD4 Series Instruction Manual preview
PSD4 Series
Бренд: halstrup-walcher Страницы: 39
Lattice LatticeMico8 User Manual preview
LatticeMico8
Бренд: Lattice Страницы: 23
Maguire Products GRAVIMETRIC AUGER FEEDER MGF-ST Instruction Manual preview
GRAVIMETRIC AUGER FEEDER MGF-ST
Бренд: Maguire Products Страницы: 47
Magtrol DSP7000 User Manual preview
DSP7000
Бренд: Magtrol Страницы: 160
Samson FOUNDATION 3730-5 Mounting And Operating Instructions preview
FOUNDATION 3730-5
Бренд: Samson Страницы: 132
Samson 3767 Mounting And Operating Instructions preview
3767
Бренд: Samson Страницы: 68
Samson 3730-2 Mounting And Operating Instructions preview
3730-2
Бренд: Samson Страницы: 128
Samson 3725 series Mounting And Operating Instructions preview
3725 series
Бренд: Samson Страницы: 68
Samson TROVIS 3730-1 Mounting And Operating Instructions preview
TROVIS 3730-1
Бренд: Samson Страницы: 80
Haehne DCX Quick Start Manual preview
DCX
Бренд: Haehne Страницы: 44
YOKOGAWA UP150 Instruction Manual preview
UP150
Бренд: YOKOGAWA Страницы: 33
Webasto Thermo Call TC3 Installation Instructions Manual preview
Thermo Call TC3
Бренд: Webasto Страницы: 15

Бренды по названию

Популярные бренды

Загрузить еще бренды