manualshive.com logo in svg

Texas Instruments TMS320 2806 Series, Техническое справочное руководство


Поделиться
Скачать
background image

I2CXSR

I2CDXR

I2CRSR

I2CDRR

Clock

synchronizer

Prescaler

Noise filters

Arbitrator

I2C INT

Peripheral bus

Interrupt to
CPU/PIE

SDA

SCL

Control/status

registers

CPU

I2C module

TX FIFO

RX FIFO

FIFO Interrupt
to CPU/PIE

Figure 14-2. I2C Module Conceptual Block Diagram

 

14.1.5 Clock Generation

The I2C module clock determines the frequency at which the I2C module operates. A programmable prescaler in 
the I2C module divides down the SYSCLK to produce the I2C module clock and this I2C module clock is divided 
further to produce the I2C master clock on the SCL pin. 

Figure 14-3

 shows the clock generation diagram for I2C 

module.

 1

SYSCLK

I2C Module Clock

(ICCL + d) + (ICCH + d)

Master Clock on SCL pin

Figure 14-3. Clocking Diagram for the I2C Module

 

Note

To meet all of the I2C protocol timing specifications, the I2C module clock must be between 7-12 MHz.

www.ti.com

Inter-Integrated Circuit Module (I2C)

SPRUH18I – JANUARY 2011 – REVISED JUNE 2022

Submit Document Feedback

TMS320x2806x Microcontrollers

837

Copyright © 2022 Texas Instruments Incorporated

Содержание TMS320 2806 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320 2806 Series

FAAC 740 D User Manual preview
740 D
Бренд: FAAC Страницы: 64
GAUGEMASTER COMBI Manual preview
COMBI
Бренд: GAUGEMASTER Страницы: 2
EasyIO FC Series Firmware Upgrade User Manual preview
FC Series
Бренд: EasyIO Страницы: 19
PAC 212 Install Manual preview
212
Бренд: PAC Страницы: 17
Mita WP3000 Manual preview
WP3000
Бренд: Mita Страницы: 7
MQ Multiquip DCA20SPXU2 Operation And Parts Manual preview
DCA20SPXU2
Бренд: MQ Multiquip Страницы: 74
AMALGAMATED INSTRUMENT PM4-RT8 Operation And Instruction Manual preview
PM4-RT8
Бренд: AMALGAMATED INSTRUMENT Страницы: 27
Samson 3375 Mounting And Operating Instructions preview
3375
Бренд: Samson Страницы: 130
Maxon 688770 Hardware Reference Manual preview
688770
Бренд: Maxon Страницы: 64
PacComm TINY-2 Technical Reference Manual preview
TINY-2
Бренд: PacComm Страницы: 29
Tektronix 7M13 Instruction Manual preview
7M13
Бренд: Tektronix Страницы: 34
Conrad SPC-1 Operating Instructions preview
SPC-1
Бренд: Conrad Страницы: 2
Advantech ADAM-5511 Manual preview
ADAM-5511
Бренд: Advantech Страницы: 340
Tekmar D 650 Data Brochure preview
D 650
Бренд: Tekmar Страницы: 4
Magnetek GPD 333 Technical Manual preview
GPD 333
Бренд: Magnetek Страницы: 81
Parasound AVC-2500u Brochure & Specs preview
AVC-2500u
Бренд: Parasound Страницы: 2
Clare Controls CH-OS-L Installation Sheet preview
CH-OS-L
Бренд: Clare Controls Страницы: 5
Xantrex SOLAR CHARGE CONTROLLER 30 Owner'S Manual preview
SOLAR CHARGE CONTROLLER 30
Бренд: Xantrex Страницы: 40

Бренды по названию

Популярные бренды

Загрузить еще бренды