manualshive.com logo in svg

Texas Instruments TMS320 2806 Series, Техническое справочное руководство


Поделиться
Скачать
background image

Table 11-9. Control Register (CONTROL) Field Descriptions (continued)

Bit

Field

Value Description

7

ERRCLR

0

Error Clear Bit: Writing a 1 to this bit will clear any latched sync error event and clear the 
SYNCERR bit. This bit will also clear the OVRFLG bit. This bit would normally be used when 
initializing the DMA for the first time or if an overflow condition is detected. If an ADCSYNC error 
event or overflow event occurs at the same time as writing to this bit, the ADC or overrun has 
priority and the SYNCERR or OVRFLG bit is set.

6-5

Reserved

Reserved

4

PERINTCLR

0

Peripheral Interrupt Clear Bit: Writing a 1 to this bit clears any latched peripheral interrupt event 
and clears the PERINTFLG bit. This bit would normally be used when initializing the DMA for the 
first time. If a peripheral event occurs at the same time as writing to this bit, the peripheral has 
priority and the PERINTFLG bit is set.

3

PERINTFRC

0

Peripheral Interrupt Force Bit: Writing a 1 to this bit latches a peripheral interrupt event trigger 
and sets the PERINTFLG bit. If the PERINTE bit is set, this bit can be used like a software force 
for a DMA burst transfer.

2

SOFTRESET

0

Channel Soft Reset Bit: Writing a 1 to this bit completes current read-write access and places the 
channel into a default state as follows:

RUNSTS = 0

TRANSFERSTS = 0

BURSTSTS = 0

BURST_COUNT = 0

TRANSFER_COUNT = 0

SRC_WRAP_COUNT = 0

DST_WRAP_COUNT = 0

This is a 

soft

 reset that basically allows the DMA to complete the current read-write access and 

then places the DMA channel into the default reset state.

1

HALT

0

Channel Halt Bit: Writing a 1 to this bit halts the DMA at the current state and any current 
read-write access is completed. See 

Figure 11-5

 for the various positions the state machine can 

be at when HALTED. The RUNSTS bit is set to 0. To take the device out of HALT, the RUN bit 
needs to be activated.

0

RUN

0

Channel Run Bit: Writing a 1 to this bit starts the DMA channel. The RUNSTS bit is set to 1. This 
bit is also used to take the device out of HALT.

The RUN bit is typically used to start the DMA running after you have configured the DMA. It 
will then wait for the first interrupt event (PERINTFLG == 1) to start operation. The RUN bit can 
also be used to take the DMA channel out of a HALT condition See 

Figure 11-5

 for the various 

positions the state machine can be at when HALTED.

www.ti.com

Direct Memory Access (DMA) Module

SPRUH18I – JANUARY 2011 – REVISED JUNE 2022

Submit Document Feedback

TMS320x2806x Microcontrollers

749

Copyright © 2022 Texas Instruments Incorporated

Содержание TMS320 2806 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320 2806 Series

Fairchild 63 Installation, Operation And Maintenance Instructions preview
63
Бренд: Fairchild Страницы: 2
TCS Basys Controls QD Series Troubleshooting Worksheet preview
QD Series
Бренд: TCS Basys Controls Страницы: 2
Accel 300+ Installation Instructions Manual preview
300+
Бренд: Accel Страницы: 8
K1EL WinKeyer3 Operation Manual preview
WinKeyer3
Бренд: K1EL Страницы: 46
CP Electronics AR-SG-4SM-W Product Manual preview
AR-SG-4SM-W
Бренд: CP Electronics Страницы: 12
Oomlout ARDX Experimenter'S Manual preview
ARDX
Бренд: Oomlout Страницы: 32
Inca PSJ2 User Manual preview
PSJ2
Бренд: Inca Страницы: 11
Estyma iGNEO COMPACT User Manual preview
iGNEO COMPACT
Бренд: Estyma Страницы: 56
Instruments of Things IO-Lights User Manual preview
IO-Lights
Бренд: Instruments of Things Страницы: 12
Knoll MR173 Installation And Operating Instructions preview
MR173
Бренд: Knoll Страницы: 3
Epsolar LS1024RP Instruction Manual preview
LS1024RP
Бренд: Epsolar Страницы: 32
Open Grow GroLab TankBot Installation Manual preview
GroLab TankBot
Бренд: Open Grow Страницы: 20
Elettronica Santerno Sinus Penta Series Applications Manual preview
Sinus Penta Series
Бренд: Elettronica Santerno Страницы: 140
Zero 88 01-201-00 Operating Manual preview
01-201-00
Бренд: Zero 88 Страницы: 34
DNF Controls 2MCE-24P User Manuals preview
2MCE-24P
Бренд: DNF Controls Страницы: 19
Worcester DT10RF Instruction Manual preview
DT10RF
Бренд: Worcester Страницы: 24
Cylon American Auto-Matrix Aspect Matrix MAX Hardware Installation Manual preview
American Auto-Matrix Aspect Matrix MAX
Бренд: Cylon Страницы: 12
Segway InfoKey Manual preview
InfoKey
Бренд: Segway Страницы: 32

Бренды по названию

Популярные бренды

Загрузить еще бренды