Stanford Research Systems SR785 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 546

background image

1-24 Octave

Analysis

SR785 Dynamic Signal Analyzer

4. Press [Source]

Select the Source menu.

Press

<Noise>

Choose Noise as the source type. Octave
measurements are generally used to measure noise.

Press

<Type>

Change the type of noise.

Use the knob to select (Pink) and press [Enter].

Choose Pink noise. Pink noise rolls off at -3dB per
octave. This maintains equal power per octave band
and yields a flat octave spectrum.

Press [Auto Range Ch1] and [Auto Range Ch2].

Adjust the input ranges to remove overloads.

Notice that the measurement needs to settle after
the input range is changed. This is because the
measurement is invalid until the input change has
propagated through all of the octave band filters.
This settling time is related to 1/bandwidth of each
filter. Bands which are un-settled are graphed in
half intensity. ‘Settle’ is displayed until all bands in
the display are settled.

Press [Auto Scale A] and [Auto Scale B].

DisplayA (Ch1) shows the flat source spectrum and
DisplayB (Ch2) shows the notch filter output.

5. Press [Average]

Select the Average menu. Note that this menu is
changed in Octave group.

Press <Integration Time>

The Integration Time is the averaging time
constant. All Octave measurements are rms
averaged.

Press [1], select (s) with the knob, and press
[Enter].

Increase the Integration Time to smooth the
fluctuations in the spectrum.

6. Press [Freq]

Select the Frequency menu.

Press <Octave Resolution>

Change the number of bands per octave.

Use the knob to select (Full) and press [Enter].

Choose Full octave bands.

Each band represents a full octave with very poor
frequency resolution.

Press <Octave Resolution>

Change the number of bands per octave again.

«
...
38
39
40
41
42
...
»

Содержание SR785



































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SR785

Бренд: 3nh Страницы: 10

Бренд: Omer Страницы: 2

Бренд: C-LOGIC Страницы: 4

Бренд: C-lock Страницы: 32

Бренд: C-LOGIC Страницы: 12

TEC SourceMeter 2510

Бренд: Keithley Страницы: 244

Бренд: Kawai Страницы: 112

Бренд: Jenoptik Страницы: 54

Бренд: Macnaught Страницы: 8

Бренд: Solartron Mobrey Страницы: 34

Бренд: Keller Страницы: 8

Бренд: PCE Health and Fitness Страницы: 11

WM14-96 - PROGRAMMING

Бренд: CARLO GAVAZZI Страницы: 6

WD-35606-00, WD-35606-05

Бренд: Oakton Страницы: 10

Бренд: Fuji Electric Страницы: 85

Бренд: Hanna Instruments Страницы: 25

Бренд: Laser Technology Страницы: 80

Бренд: Maxtec Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды