manualshive.com logo in svg

Stanford Research Systems SR785, Руководство по эксплуатации и программированию


Поделиться
Скачать
background image

 

 

Swept Sine Measurements  2-51 

 

SR785 Dynamic Signal Analyzer 

 

 

The Integration Time is always an exact number of cycles at the source frequency. This 
rejects signals which are at a different frequency, such as noise and harmonics. A long 
Integration Time results in a narrow detection bandwidth at the source frequency. This 
improves signal to noise at the cost of longer measurement times . This is similar to the 
linewidth of an FFT. However, in the FFT the linewidth is exactly related to the 
frequency span (Span/FFT Resolution). In swept sine, the Integration Time is 
independent of the frequency span. Thus, wide spans can be measured with narrow line 
widths. 

The Integration Time is specified in both time and cycles of the source. Times are 
converted to the next larger exact number of cycles. The larger of the two specifications 
is used as the Integration Time. A minimum of 1 cycle or 15.6 ms is always measured. 
To measure each point with the same linewidth, set the Integration Cycles to 1 and the 
Integration Time to 1/linewidth. To measure each point for a time inversely proportional 
to the frequency, set the Integration Time to 15.6 ms and the Integration Cycles to the 
desired number. Remember, the detection bandwidth increases with frequency in this 
case (the cycles get shorter) which may result in increased detected noise at higher 
frequencies.  

When the integration is complete, the source moves to the next frequency in the sweep. 
A Settle Time is allowed to pass before any measurement is made at the inputs. This 
allows the device under test to respond to the frequency change. This can be especially 
important if the device under test has a high Q. The Settle Time is also specified in both 
time and cycles of the source. Times are converted to cycles and the larger of the two 
specified cycles is used. 

The Integration and Settle Times are set within the [Average] menu. 

Sweep Frequency and Auto Resolution 

The span of a swept sine sweep is determined by the Start and Stop frequencies. The 
entire 102.4 kHz frequency range of the SR785 is available for swept sine measurements. 
Note that starting a sweep at DC is not possible. In fact, beware of starting at any 
frequency much less than 1 Hz since the Settle and Integration times are always a 
minimum of 1 cycle. If the start frequency is very low, the first point can take longer to 
measure than the entire remainder of the sweep!  

The Sweep Number Of Points, or resolution, can be set from 10 to 2047. The points can 
be in a linear or a logarithmic progression. In many cases it is desirable to sweep over a 
wide frequency range while still detecting narrow features in the response function. An 
example might be a filter with many zeroes or a narrow notch. In order to resolve the 
narrow features, a large number of points must be used in the sweep to improve the 
frequency resolution. However, a large amount of the sweep time will be spent 
measuring points between the features of interest. This is where Auto Resolution can 
save measurement time while preserving resolution. 

Auto Resolution is specified by three parameters, the Faster Threshold, the Slower 
Threshold and the Maximum Step Size. As with all frequency parameters, these are set 
within the [Frequency] menu. 

Содержание SR785



































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SR785

rainforest EMU Quick Start Manual preview
EMU
Бренд: rainforest Страницы: 2
Aaronia SPECTRAN V5 Manual preview
SPECTRAN V5
Бренд: Aaronia Страницы: 47
Kawai EP3 Owner'S Manual preview
EP3
Бренд: Kawai Страницы: 66
Kane 457 Quick Reference Manual preview
457
Бренд: Kane Страницы: 16
Kane 457 Manual preview
457
Бренд: Kane Страницы: 60
Ulvac SPU Instruction Manual preview
SPU
Бренд: Ulvac Страницы: 24
DGH DGH 55B Operator'S Manual preview
DGH 55B
Бренд: DGH Страницы: 87
Danfoss AK-LM 330 Design Manual preview
AK-LM 330
Бренд: Danfoss Страницы: 80
Dusty Strings Dusty Harp Pickup Series Installation Instructions preview
Dusty Harp Pickup Series
Бренд: Dusty Strings Страницы: 5
Fronius LaserHybrid SB 360i Operating Instructions Manual preview
LaserHybrid SB 360i
Бренд: Fronius Страницы: 104
LaserLine GL3000PM Owner'S Manual preview
GL3000PM
Бренд: LaserLine Страницы: 11
Jaquet T411 Operating Instructions Manual preview
T411
Бренд: Jaquet Страницы: 27
PCE Instruments PCE-VT 1000 Manual preview
PCE-VT 1000
Бренд: PCE Instruments Страницы: 6
3M SP-SE-2-1/1 User Manual preview
SP-SE-2-1/1
Бренд: 3M Страницы: 168
Lambda SRS SR475 Operation Manual preview
SRS SR475
Бренд: Lambda Страницы: 35
Xylem WTW SensoLyt 900 Operating Manual preview
WTW SensoLyt 900
Бренд: Xylem Страницы: 12
MSA AUER Atemluft 300 bar Operating Manual preview
AUER Atemluft 300 bar
Бренд: MSA Страницы: 52
Heyuan Intelligence DZ81-MA3UI5C User Manual preview
DZ81-MA3UI5C
Бренд: Heyuan Intelligence Страницы: 14

Бренды по названию

Популярные бренды

Загрузить еще бренды