Juniper JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010 Скачать руководство пользователя

Страница: 597 / 774

■

ignore-df-bit—Specifies that the don’t-fragment bit is ignored

■

inactivity-timer—Configures an inactivity timer value for IP interfaces

■

inspection—Associates an inspection list to the interface for firewalling

■

mtu—Configures the MTU for a network

■

nat—Configures the interface as inside or outside for Network Address Translation
(NAT)

■

policy—Assigns a policy to the ingress or egress of an interface

■

redirects—Enables transmission of ICMP redirect messages

■

route-cache flow sampled—Enables J-Flow statistics on an interface

■

route-map ip-subscriber—Configures the interface for route-map processing

■

sa-validate—Verifies that a packet has been sent from a valid source address

■

tcp adjust-mss—Modifies maximum segment size (MSS) on TCP connections
when path MTU detection is not sufficient

■

unnumbered—Configures IP on this interface without a specific address

■

virtual-router—Specifies a virtual router (VR) to which interfaces created by this
profile attach

IPv6 Characteristics

A profile can contain one or more of the following IPv6 characteristics:

■

address—Configures an IPv6 address on an interface

■

http—Configures the HTTP local server for IPv6

■

http redirectUrl—Configures the URL to which a subscriber’s initial Web browser
session is redirected

■

nd—Enables Neighbor Discovery on an interface

■

nd managed-config-flag—Sets the “managed address configuration” flag in IPv6
router advertisements

■

nd other-config-flag—Sets the “other stateful configuration” flag in IPv6 router
advertisements

■

nd prefix-advertisement—Specifies which IPv6 prefixes are included in IPv6
router advertisements

■

nd ra-interval—Configures the interval between IPv6 router advertisements

■

nd ra-lifetime—Configures the router advertisement lifetime

■

nd reachable-time—Configures the amount of time the router can reach an IPv6
node after a reachability confirmation event occurs

■

nd suppress-ra—Disables router advertisement transmissions

■

mld—Configures the multicast listener discovery (MLD) interface

■

mtu—Configures the MTU for a network

■

policy—Attaches (or removes) a policy to (or from) an interface

Configuring a Dynamic Interface from a Profile

■

565

Chapter 17: Configuring Dynamic Interfaces

Содержание JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010







































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

Отзывы:

Похожие инструкции для JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

Бренды по названию

Популярные бренды

Juniper JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010, Руководство по настройке

Результаты поиска

Содержание JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

Отзывы:

Похожие инструкции для JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

Бренды по названию

Популярные бренды