Juniper JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010 Скачать руководство пользователя

Страница: 86 / 774

■

Use to configure F5 OAM VC integrity parameters on an ATM data PVC.

■

You can optionally specify the following values:

■

upRetryCount

—Number of successive loopback cell responses, in the range

1–60, for the router to receive before reporting that a PVC is up; default
value is 3

■

downRetryCount

—Number of successive loopback cell responses, in the range

1–60, for the router to miss before reporting that a PVC is down; default
value is 5

■

retryFrequency

—Number of seconds, in the range 1–600, for the router to

wait between the transmission of loopback cells when it is verifying the state
of the PVC; default value is 1

■

To configure these VC integrity parameters, you must use the

oam retry

command in ATM VC Configuration mode. There is no equivalent

atm pvc

command to configure these parameters.

■

You must issue the

exit

command from ATM VC Configuration mode for the

configuration to take effect.

■

Example

host1(config-subif-atm-vc)#

oam retry 5 6 3

host1(config-subif-atm-vc)#

exit

■

Use the

version to restore the default values for the up retry count, down

retry count, and retry frequency parameters.

■

See oam retry.

Configuring Inverse ARP for Data PVCs

You can use the

inarp

command in ATM VC Configuration mode to enable Inverse

ARP (InARP) on a data PVC that resides on an ATM 1483 NBMA subinterface
configured with the

multipoint

option. The PVC must use the default encapsulation

method,

aal5snap

. For more information about InARP, see “Configuring an NBMA

Interface” on page 39.

For example, the following commands enable InARP with a nondefault refresh rate
(10 minutes) on a data PVC. The PVC uses

aal5snap

encapsulation by default. Issuing

the

exit

command causes the configuration to take effect.

host1(config)#

interface atm 3/2.1 multipoint

host1(config-subif)#

pvc 6 0/11

host1(config-subif-atm-vc)#

inarp 10

host1(config-subif-atm-vc)#

exit

host1(config-subif)#

inarp

■

Configuring Individual ATM PVC Parameters

JUNOSe 11.1.x Link Layer Configuration Guide

Содержание JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010







































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

Отзывы:

Похожие инструкции для JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

Бренды по названию

Популярные бренды

Juniper JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010, Руководство по настройке

Результаты поиска

Содержание JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

Отзывы:

Похожие инструкции для JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

Бренды по названию

Популярные бренды