Juniper JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010 Скачать руководство пользователя

Страница: 307 / 774

Before You Configure PPP

Before you configure a PPP interface, configure the interface or tunnel over which
PPP traffic will flow. See the following chapters:

■

Configuring Channelized T3 Interfaces in

JUNOSe Physical Layer Configuration

Guide

■

Configuring T3 and E3 Interfaces in

JUNOSe Physical Layer Configuration Guide

■

Configuring Unchannelized OCx/STMx Interfaces in

JUNOSe Physical Layer

Configuration Guide

■

Managing Tunnel-Service and IPSec-Service Interfaces in

JUNOSe Physical Layer

Configuration Guide

■

“Configuring ATM” on page 3

■

“Configuring Packet over SONET” on page 363

■

“Configuring Point-to-Point Protocol over Ethernet” on page 375

The procedures described in this chapter assume that a physical interface has been
configured.

Configuration Tasks

The following procedure is an example of a PPP configuration on a serial interface.
These steps are mandatory unless otherwise noted.

From Global Configuration mode, specify the physical interface on which you
want to configure PPP.

host1(config)#

interface serial 3/0:2/5

Specify PPP as the encapsulation method (data-link protocol) on the interface.

host1(config-if)#

encapsulation ppp

Assign an IP address and subnet mask for the interface.

host1(config-if)#

ip address 192.168.22.10 255.255.255.0

Verify that your configuration changes are correct.

host1#

show ppp interface serial 3/0:2/5 config

encapsulation ppp

■

Use to configure PPP as the encapsulation method.

■

Example

host1(config-if)#

encapsulation ppp

Before You Configure PPP

■

275

Chapter 8: Configuring Point-to-Point Protocol

Содержание JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010







































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

Отзывы:

Похожие инструкции для JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

Бренды по названию

Популярные бренды

Juniper JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010, Руководство по настройке

Результаты поиска

Содержание JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

Отзывы:

Похожие инструкции для JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

Бренды по названию

Популярные бренды