Juniper JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010 Скачать руководство пользователя страница 220 | Manualshive

Страница: 220 / 774

background image

host1(config-if)#

svlan id 1000 any

■

There is no

no

version.

■

See svlan id.

S-VLAN Oversubscription

When you configure S-VLAN subinterfaces over Ethernet interfaces to support dynamic
PPPoE subinterfaces, you can take advantage of S-VLAN oversubscription.

The following module combinations support S-VLAN oversubscription:

■

GE/FE line module and all of its associated I/O modules

■

GE-2 line module and the GE-2 SFP I/O module

■

GE-HDE line module and its associated I/O modules

■

OC3/STM1 GE/FE line module and the OC3-2 GE APS I/O module

■

ES2 4G LM and its associated Gigabit Ethernet and 10-Gigabit Ethernet IOAs

■

ES2 10G LM and its associated Gigabit Ethernet and 10-Gigabit Ethernet IOAs

The maximum number of S-VLANs that you can create per I/O module with PPPoE
major interfaces stacked over them is greater than the maximum number of dynamic
PPPoE subinterfaces. The maximum number of PPP interfaces supported per line
module is directly proportional to the maximum number of PPPoE subinterfaces.

As a result, you can oversubscribe S-VLANs by configuring up to the maximum
number of S-VLANs supported on these I/O modules, knowing that no more than
the maximum number of supported PPP sessions can be connected to the router at
any one time.

For configuration instructions, see “Configuring Dynamic PPPoE over Static PPPoE
with Ethernet and S-VLAN Interface Columns” on page 542 in “Configuring Dynamic
Interfaces” on page 515.

For specific information about the maximum number of S-VLANs supported per I/O
module and the maximum number of PPP interfaces and PPPoE subinterfaces
supported per line module, see

JUNOSe Release Notes

,

Appendix A

,

System Maximums

.

NOTE:

The E120 and E320 routers can support up to two IOAs per line module. This

maximum number of S-VLANs per line module does not change if one or two IOAs
are installed.

Monitoring VLAN and S-VLAN Subinterfaces

This section explains how to display bit rate and packet rate statistics for VLAN
subinterfaces and use the

show

commands to display the physical characteristics

and the configured settings for VLAN and S-VLAN subinterfaces.

188

■

S-VLAN Oversubscription

JUNOSe 11.1.x Link Layer Configuration Guide

«
...
218
219
220
221
222
...
»

Содержание JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010







































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

Бренд: McDATA Страницы: 170

Бренд: ICP Страницы: 16

NETWORK BASIC - USER REFERENCE GUIDE 4.0

Бренд: Red Hat Страницы: 92

VIRUSSCAN ENTERPRISE

Бренд: McAfee Страницы: 2

PTF100NTU - LCD PROJECTOR

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 10

Media Manager V2.1

Бренд: Panasonic Страницы: 28

Lumix VQT0U14 ( )

Бренд: Panasonic Страницы: 36

Бренд: Panasonic Страницы: 70

PANATERM Ver. 3.7

Бренд: Panasonic Страницы: 78

Voice Editing Ver.2.0

Бренд: Panasonic Страницы: 132

Бренд: Panasonic Страницы: 156

Cycos ERGO mrs 5.0

Бренд: Cycos Страницы: 46

Бренд: Packet8 Страницы: 43

Бренд: Lowrance Страницы: 80

Бренд: Lowrance Страницы: 108

AURORA INGEST 7

Бренд: GRASS VALLEY Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды