Juniper JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010 Скачать руководство пользователя страница 223 | Manualshive

Страница: 223 / 774

background image

■

Output bps/pps—Number of bits per second (bps) and packets per second
(pps) transmitted on this interface during the specified load interval

■

Time—Time of day, in hh:mm:ss format, at which the router calculates the
bit rate and packet rate statistics for the current interval

■

Example 1—Displays bit rate and packet rate statistics over the default (5-second)
load interval for a single VLAN subinterface

host1#

monitor vlan interface fastEthernet 0/0.1

Seconds
between
Interface polls Input bps/pps Output bps/pps
----------------------- -------- --------------- ---------------
FastEthernet 0/0.1 0 --/-- --/--
FastEthernet 0/0.1 5 120240/100 120240/100
FastEthernet 0/0.1 5 120000/100 120000/100
FastEthernet 0/0.1 5 92400/77 92400/77
FastEthernet 0/0.1 5 88800/74 88800/74
FastEthernet 0/0.1 5 120000/100 120000/100
host1#

^C

■

Example 2—Displays bit rate and packet rate statistics over a 10-second load
interval for two VLAN subinterfaces, with the time of day that the statistics were
calculated

host1#

monitor vlan interface fastEthernet 0/0.1 fastEthernet 4/0.1

load-interval 10 display-time-of-day

Seconds
between Time
Interface polls Input bps/pps Output bps/pps (UTC)
----------------------- -------- --------------- --------------- --------
FastEthernet 0/0.1 0 --/-- --/-- 10:50:33
FastEthernet 4/0.1 0 --/-- --/-- 10:50:33
FastEthernet 0/0.1 10 120120/100 120120/100 10:50:43
FastEthernet 4/0.1 10 120000/100 120000/100 10:50:43
FastEthernet 0/0.1 10 120000/100 120000/100 10:50:53
FastEthernet 4/0.1 10 120000/100 120000/100 10:50:53
host1#

^C

■

There is no

no

version.

■

See monitor vlan interface.

Using Ethernet show Commands

Use the

show

commands described in this section to display information about your

Ethernet configuration and to monitor Ethernet interfaces.

show interfaces fastEthernet

■

Use to display the status of Fast Ethernet interfaces, VLAN subinterfaces, or
S-VLAN subinterfaces.

■

You can specify the following keywords:

■

delta

—Specifies that baselined statistics are to be shown

Monitoring VLAN and S-VLAN Subinterfaces

■

191

Chapter 5: Configuring VLAN and S-VLAN Subinterfaces

«
...
221
222
223
224
225
...
»

Содержание JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010







































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

WJ-ND300 Administrator Console

Бренд: Panasonic Страницы: 27

3C16120 - SuperStack 3 Server Load Balancer

Бренд: 3Com Страницы: 20

Codian Remote Management API

Бренд: TANDBERG Страницы: 66

2950C-24 - Catalyst Switch - Stackable

Бренд: Cisco Страницы: 18

CONFERENCING EXTENSIONS - ADMINISTRATOR GUIDE FOR MICROSOFT EXCHANGE

Бренд: Cisco Страницы: 61

Cisco mds 9124 - fabric switch

Бренд: Cisco Страницы: 9

Бренд: Cisco Страницы: 16

Cisco MDS 9020 - Fabric Switch

Бренд: Cisco Страницы: 22

Бренд: Cisco Страницы: 13

Cisco mds 9124 - fabric switch

Бренд: Cisco Страницы: 3

Бренд: Cisco Страницы: 7

Бренд: Cisco Страницы: 74

Craft Works Interface

Бренд: Cisco Страницы: 32

Catalyst Series Switch 2940

Бренд: Cisco Страницы: 82

Catalyst Series Switch 2940

Бренд: Cisco Страницы: 28

Бренд: Cisco Страницы: 58

CCNA NETWORK SIMULATOR

Бренд: Cisco Страницы: 88

CSACSE-1111-K9 - Secure Access Control Server Solution Engine

Бренд: Cisco Страницы: 130

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды