Juniper JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010 Скачать руководство пользователя страница 671 | Manualshive

Страница: 671 / 774

background image

For example, the following commands configure nested profile assignments for
the PPP and IP upper-interface encapsulation types, and define additional
attributes for the PPPoE upper-interface encapsulation type.

host1(config-profile)#

atm atm1483 profile ppp myPppProfile

host1(config-profile)#

atm atm1483 profile ip myIpProfile

host1(config-profile)#

pppoe duplicate-protection

host1(config-profile)#

pppoe sessions 3000

5.

Exit Profile Configuration mode.

6.

Configure the ATM and ATM AAL5 interface.

host1(config)#

interface atm 5/0

7.

Configure a range of VCs on the static ATM AAL5 interface, and assign a name
to this range. This operation can take several minutes to complete, depending
on the number of VCs being configured.

NOTE:

For information about the maximum number of ATM 1483 bulk configurations

supported per chassis, see

JUNOSe Release Notes

,

Appendix A

,

System Maximums

.

For example, the following command creates a VC range named myBulkConfig
made up of two VC subranges that configure a total of 5,000 virtual circuits.

host1(config-if)#

atm bulk-config myBulkConfig vc-range 0 2 101 1100

vc-range 3 6 201 700

NOTE:

For information about the maximum number of VCs (sum of the VPI/VCI

addresses within all VC subranges) that you can configure with the

atm bulk-config

command per line module and per chassis, see

JUNOSe Release Notes

,

Appendix A

,

System Maximums

.

Do not use any reserved VCI values when configuring VCs with the

atm bulk-config

command. For information about reserved VCIs, see “Configuring F4 OAM” on
page 33 in “Configuring ATM” on page 3.

8.

Assign the base profile configured for the ATM 1483 subinterface to the VC range
configured on the ATM AAL5 interface.

host1(config-if)#

profile atm1483 bulk-config-name myBulkConfig

atm1483BaseProfile

9.

Configure the ATM AAL5 interface to support autodetection of the ATM 1483
dynamic encapsulation type.

host1(config-if)#

auto-configure atm1483

atm atm1483 advisory-rx-speed

Configuring ATM 1483 Dynamic Subinterfaces

■

639

Chapter 18: Configuring Dynamic Interfaces Using Bulk Configuration

«
...
669
670
671
672
673
...
»

Содержание JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010







































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

RS232 interface for GT47 embedded apps UART

Бренд: Sony Ericsson Страницы: 14

ANTI-VIRUS FOR MIMESWEEPER -

Бренд: F-SECURE Страницы: 44

Бренд: Amazon Страницы: 60

Configuring Arrays

Бренд: HP Страницы: 132

Бренд: HP Страницы: 26

Бренд: HP Страницы: 35

460C - Deskjet Color Inkjet Printer

Бренд: HP Страницы: 24

Бренд: HP Страницы: 201

BB118BV - StorageWorks Data Protector Express Package

Бренд: HP Страницы: 365

BB118BV - StorageWorks Data Protector Express Package

Бренд: HP Страницы: 35

2605dtn - Color LaserJet Laser Printer

Бренд: HP Страницы: 372

e-diagtools 4.0

Бренд: HP Страницы: 74

GForce M-Tron Pro

Бренд: M-Audio Страницы: 4

DRUM AND BASS RIG

Бренд: M-Audio Страницы: 3

BD DISCRECORDER

Бренд: Ulead Страницы: 18

DEVICE-MAPPER MULTIPATH 4.6

Бренд: Red Hat Страницы: 42

AVGPREP 8.5 - V 85.1

Бренд: AVG Страницы: 4

Total Control Mobile

Бренд: URC Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды