Juniper JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010 Скачать руководство пользователя страница 492 | Manualshive

Страница: 492 / 774

background image

Configuring Higher-Level Protocols over S-VLANs

The procedures for configuring IP, PPPoE, and MPLS protocols over S-VLANs on
bridged Ethernet interfaces are identical to the procedures for configuring these
protocols over VLANs on bridged Ethernet interfaces.

This section provides an example for configuring PPPoE interfaces over S-VLAN
subinterfaces configured on bridged Ethernet. For descriptions of the commands
used in this procedure, see “Configuring Higher-Level Protocols over VLANs” on
page 454.

To configure PPPoE over S-VLAN over a bridged Ethernet interface:

1.

Follow the steps in “Configuring S-VLAN Subinterfaces over Bridged Ethernet”
on page 458 to configure the S-VLAN subinterface.

2.

Create a PPPoE major interface on the S-VLAN subinterface.

host1(config-subif)#

pppoe

3.

Exit the subinterface context.

host1(config-subif)#

exit

4.

Create a PPPoE subinterface by adding a subinterface number to the interface
identification command.

host1(config)#

pppoe subinterface atm 3/1.1.1.1

5.

Specify PPP as the encapsulation method on the interface.

host1(config-subif)#

encapsulation ppp

6.

Assign an IP address and mask to the interface.

host1(config-subif)#

ip address 10.1.2.3 255.255.255.255

Configuring the MTU Size for Bridged Ethernet

You can use the

bridge1483 mtu

command to configure a nondefault maximum

transmission unit (MTU) size, in bytes, for a bridged Ethernet interface. The default
MTU size for a bridged Ethernet interface is 1518 bytes.

Because you configure a bridged Ethernet interface over an ATM 1483 subinterface,
the MTU size set with the

bridge1483 mtu

command is limited by the MTU set for

the underlying ATM 1483 subinterface. As a result, the

bridge1483 mtu command

requires you to configure an

MTU size for the bridged Ethernet interface that does

not exceed the maximum allowable MTU size for the underlying ATM 1483
subinterface, 9180 bytes.

The configured MTU size for an interface is referred to as its

administrative MTU

, and

the MTU size at which the interface actually operates is referred to as its

operational

460

■

Configuring the MTU Size for Bridged Ethernet

JUNOSe 11.1.x Link Layer Configuration Guide

«
...
490
491
492
493
494
...
»

Содержание JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010







































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

GigaStudio 3.04

Бренд: Tascam Страницы: 2

GARDTEC SPEECH DIALLER

Бренд: GARDINER TECHNOLOGY Страницы: 38

Бренд: PS Audio Страницы: 6

MultiSite Configurator

Бренд: Altigen Страницы: 10

08011-41-UD2-003

Бренд: Canon Страницы: 176

Бренд: MACROMEDIA Страницы: 830

OpenView Storage Area Manager (SAM) 3.1

Бренд: HP Страницы: 13

Бренд: HP Страницы: 85

Pro 3405 Series

Бренд: HP Страницы: 9

Бренд: HP Страницы: 2

Pavilion u600 - Desktop PC

Бренд: HP Страницы: 2

Бренд: HP Страницы: 12

Pavilion w1000 - Desktop PC

Бренд: HP Страницы: 1

Pro 3520 Series

Бренд: HP Страницы: 15

Бренд: HP Страницы: 4

Бренд: HP Страницы: 4

Pro 3500 Series

Бренд: HP Страницы: 16

Бренд: HP Страницы: 95

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды