Juniper JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010 Скачать руководство пользователя страница 615 | Manualshive

Страница: 615 / 774

background image

■

Use the

no

version to disable initiation of IPv6.

■

See ppp initiate-ipv6.

ppp ipcp lockout

■

Use to terminate invalid IPv4 subscribers and prevent additional IPCP
negotiations.

■

When Internet Protocol version 6 Control Protocol (IPv6CP) is active, this
command enables unused IPv4 addresses, which are allocated for the IPv6
subscribers, to be available for the IPCP services for an internally defined time
interval (10 seconds). When the time interval elapses, the subscriber must connect
again to negotiate IPCP.

For more information about how the IPv4 addresses are restored, see

Chapter

7, Configuring Point-to-Point Protocol

.

■

Example

host1(config-subif)#

ppp ipcp lockout

■

Use the

no

version to disable the IPCP lockout option on the interface.

■

See ppp ipcp lockout.

ppp ipcp netmask

■

Use to specify Internet Protocol Control Protocol (IPCP) option 0x90 for each
PPP interface. By default, IPCP option 0x90 is disabled on the interface.

■

Example

host1(config-profile)#

ppp ipcp netmask

■

Use the

no

version to disable IPCP option 0x90 option on the interface.

■

See ppp ipcp netmask.

ppp ipcp prompt-option dns

Use to prompt the CPE (Customer Premises Equipment) to negotiate the IPCP
primary and secondary DNS options that are locally available with the broadband
remote access server.

■

■

Use the

no

version to disable the command

■

See ppp ipcp prompt-option dns

ppp keepalive

■

Use to specify the keepalive timeout value.

■

This command always operates in high-density keepalive mode when PPP is
layered over ATM or PPPoE.

■

When the keepalive timer expires, the interface searches for frames received
from the peer in the prior keepalive timeout seconds. If the interface finds such
frames, it does not send an LCP echo request (keepalive). Keepalive packets are
sent only if the peer is silent (no traffic was received from the peer during the

Configuring a Dynamic Interface from a Profile

■

583

Chapter 17: Configuring Dynamic Interfaces

«
...
613
614
615
616
617
...
»

Содержание JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010







































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

LaserWriter 8.x driver

Бренд: Xerox Страницы: 12

SpeechExec Dictation Recorder 1.6.0.0

Бренд: Philips Страницы: 42

Бренд: Philips Страницы: 56

Бренд: Philips Страницы: 184

BlackArmor WS 110

Бренд: Seagate Страницы: 2

CLOUD DIRECTOR 1.0

Бренд: VMware Страницы: 3

VmWare ESX Server 2.12 Deployment

Бренд: VMware Страницы: 34

Бренд: VMware Страницы: 34

Бренд: M-Audio Страницы: 15

PCoIP Technology

Бренд: EVGA Страницы: 27

Бренд: DeLorme Страницы: 34

Бренд: DCP Productions Страницы: 76

Бренд: Intel Страницы: 19

Бренд: Intel Страницы: 30

POLICY MANAGER PROXY -

Бренд: F-SECURE Страницы: 43

507B1-90A211-1301 - NavisWorks Manage 2010

Бренд: Autodesk Страницы: 472

Бренд: Genius Страницы: 3

Бренд: Genius Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды