Juniper JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010 Скачать руководство пользователя страница 485 | Manualshive

Страница: 485 / 774

background image

Configuring VLANs over Bridged Ethernet

This section describes how to create the following common static VLAN over bridged
Ethernet configurations:

■

IP over VLAN over bridged Ethernet

■

PPPoE over VLAN over bridged Ethernet

■

MPLS over VLAN over bridged Ethernet

You can also configure transparent bridging over VLANs over bridged Ethernet. For
information about configuring transparent bridging, see “Configuring Bridged
Ethernet” on page 443.

Configuring VLANs over bridged Ethernet interfaces consists of two basic tasks:

1.

Configure the layers up to and including the VLAN subinterface. The steps for
this task are common to all configurations.

2.

Configure the higher-level protocols above the VLAN subinterface.

The following sections describe how to configure VLANs over bridged Ethernet. For
more information about the commands used in these procedures, see the command
descriptions listed in alphabetical order at the end of “Configuring Higher-Level
Protocols over VLANs” on page 454.

NOTE:

Before you can remove a VLAN subinterface, you must remove the upper-layer

interface stack.

For more information about specifying ATM interfaces and subinterfaces, see Interface
Types and Specifiers in

JUNOSe Command Reference Guide

.

Configuring VLAN Subinterfaces over Bridged Ethernet

To configure a VLAN subinterface over bridged Ethernet:

1.

Create an ATM 1483 subinterface and associated PVC.

host1(config)#

interface atm 4/0.101

host1(config-subif)#

atm pvc 1 0 32 aal5snap 0 0 0

2.

Specify bridged Ethernet as the encapsulation method for the ATM 1483
subinterface.

host1(config-subif)#

encapsulation bridge1483

3.

Create a VLAN major interface by specifying VLAN as the encapsulation method
for the bridged Ethernet interface.

host1(config-subif)#

encapsulation vlan

Configuring VLANs over Bridged Ethernet

■

453

Chapter 14: Configuring Bridged Ethernet

«
...
483
484
485
486
487
...
»

Содержание JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010







































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

COLDFUSION MX 7.0.2-USING COLDFUSION MX WITH FLEX...

Бренд: MACROMEDIA Страницы: 90

Afro-Cuban Percussion

Бренд: M-Audio Страницы: 5

Бренд: McDATA Страницы: 170

UPGRADE FIRMWARE MODEM ROUTER

Бренд: Belkin Страницы: 1

Unity Express 8.0 Voice-Mail System

Бренд: Cisco Страницы: 50

TELEPRESENCE MANAGEMENT SUITE PROVISIONING

Бренд: Cisco Страницы: 16

Unified MeetingPlace H.323/SIP

Бренд: Cisco Страницы: 54

PVDM2 24DM - Digital Modem Module

Бренд: Cisco Страницы: 48

TELEPRESENCE MANAGEMENT SUITE SECURE SERVER

Бренд: Cisco Страницы: 34

Бренд: Cisco Страницы: 8

Unified Videoconferencing Manager

Бренд: Cisco Страницы: 22

SMART BUSINESS COMMUNICATIONS SYSTEM

Бренд: Cisco Страницы: 27

MDS 9222i - Multiservice Modular Fabric Switch

Бренд: Cisco Страницы: 40

MCS 7825 Series

Бренд: Cisco Страницы: 20

Surveillance Media Server

Бренд: Cisco Страницы: 14

Бренд: Cisco Страницы: 92

TelePresence Movi 4.1

Бренд: Cisco Страницы: 29

MeetingPlace Video Integration

Бренд: Cisco Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды