Juniper JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010 Скачать руководство пользователя страница 548 | Manualshive

Страница: 548 / 774

background image

You create and configure each layer of a

static interface

manually through an existing

configuration mechanism such as the command-line interface (CLI) or Simple Network
Management Protocol (SNMP).

Unlike static interfaces, dynamic interfaces are not restored through nonvolatile
storage (NVS) after a reboot.

Autodetection

The router performs

autodetection,

also referred to as

autosensing,

to determine the

layers of each dynamic interface. The autodetection process occurs when the router
conditionally constructs interface layers based on the encapsulation type of the
incoming packet.

Autodetection only uses system resources on demand based on what is detected in
the incoming packet. Dynamic interfaces are created as a result of traffic on the
interface. Dynamic interfaces can also be dynamically deleted without your
intervention, thereby enabling any consumed system resources to be returned.

Unlike dynamic interfaces, static interfaces always allocate system resources upon
creation, and always consume system resources, even when the interface is quiescent.

Types of Dynamic Interfaces

There are two types of dynamic interfaces: upper-layer and bulk-configured.
Bulk-configured dynamic interfaces enable you to dynamically create ATM 1483
subinterfaces and VLAN subinterfaces by bulk-configuring a range of identifiers.
There are two types of bulk-configured dynamic interfaces:

■

ATM 1483 interfaces over static ATM AAL5 interface

■

VLAN subinterface over static VLAN major interface

For more information, see “Configuring Dynamic Interfaces Using Bulk Configuration”
on page 623.

Upper-layer dynamic interfaces enable you to dynamically create the following
configurations:

■

Dynamic IP, PPPoE, PPP, MLPPP, and bridged Ethernet interfaces over a static
ATM 1483 interface

■

IP or PPPoE interfaces over VLAN interfaces and Ethernet, Gigabit Ethernet, and
10-Gigabit-Ethernet interfaces.

NOTE:

Ethernet interfaces in this chapter refer to any of these interfaces Fast Ethernet,

Gigabit Ethernet, or 10–Gigabit-Ethernet.

516

■

Overview

JUNOSe 11.1.x Link Layer Configuration Guide

«
...
546
547
548
549
550
...
»

Содержание JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010







































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

AccuSync LCD52V

Бренд: NEC Страницы: 5

COOL 3D-PLUG-IN MADNESS II

Бренд: Ulead Страницы: 10

Electric Bass Vol. 1—Rock

Бренд: M-Audio Страницы: 4

Бренд: Intergraph Страницы: 46

Бренд: Brady Страницы: 33

Бренд: Primera Страницы: 48

Бренд: Nero Страницы: 95

OmniPage Direct

Бренд: NUANCE Страницы: 44

Бренд: RedMoon Music Страницы: 74

Бренд: Red Hat Страницы: 188

CLUSTER SUITE FOR ENTERPRISE LINUX 5.1

Бренд: Red Hat Страницы: 160

SimpleDrive SP-U25/120

Бренд: SimpleTech Страницы: 8

POWER WAVE 405M

Бренд: Lincoln Electric Страницы: 42

Бренд: Pfaff Страницы: 8

Бренд: UNIBLUE Страницы: 3

Бренд: Online Media Technologies Страницы: 46

Gateway Routing Manager

Бренд: Bay Networks Страницы: 20

Бренд: Bay Networks Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды