Juniper JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010 Скачать руководство пользователя страница 242 | Manualshive

Страница: 242 / 774

background image

host1(config-if)#

speed 100

host1(config-if)#

duplex full

host1(config-if)#

lacp active

host1(config-if)#

interface fastEthernet 5/1

host1(config-if)#

speed 100

host1(config-if)#

duplex full

host1(config-if)#

lacp active

The following commands create a virtual router, add the Ethernet physical interfaces
to a LAG bundle named kanata, assign an IP address, and configure MPLS.

host1(config)#

virtual router kanata

host1:kanata(config)#

interface lag kanata

host1:kanata(config-if)#

member-interface fastEthernet 0/0

host1:kanata(config-if)#

member-interface fastEthernet 0/5

host1:kanata(config-if)#

ip address 1.1.1.1 255.255.255.0

host1(config-if)#

mpls

Example: Configuring MPLS over a VLAN for a LAG Bundle

The following example displays configuration of LACP for two Fast Ethernet interfaces
in slot 5. The interfaces are enabled for active LACP. The speed and duplex
characteristics are the same for both interfaces.

host1(config)#

interface fastEthernet 5/0

host1(config-if)#

speed 100

host1(config-if)#

duplex full

host1(config-if)#

lacp active

host1(config-if)#

interface fastEthernet 5/1

host1(config-if)#

speed 100

host1(config-if)#

duplex full

host1(config-if)#

lacp active

The following commands add the Ethernet physical interfaces to a LAG bundle named
kanata.

host1(config)#

virtual router kanata

host1:kanata(config)#

interface lag kanata

host1:kanata(config-if)#

member-interface fastEthernet 5/0

host1:kanata(config-if)#

member-interface fastEthernet 5/1

The following commands configure a VLAN subinterface for the LAG bundle named
kanata. In the LAG interface identification command (

interface lag kanata.1

), the

number 1 represents the subinterface number for the VLAN subinterface.

host1:kanata(config-if)#

encapsulation vlan

host1:kanata(config)#

interface lag kanata.1

host1:kanata(config-if)#

vlan id 100

The following command creates an MPLS interface.

host1:kanata(config)#

mpls

210

■

Example: Configuring MPLS over a VLAN for a LAG Bundle

JUNOSe 11.1.x Link Layer Configuration Guide

«
...
240
241
242
243
244
...
»

Содержание JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010







































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

DEEP FREEZE ENTERPRISE - PATCH MANAGEMENT...

Бренд: FARONICS Страницы: 23

PHOTOSHOP CS 2.0 - SCRIPTING GUIDE

Бренд: Adobe Страницы: 91

MPX NATIVE REVERB PLUG-IN

Бренд: Lexicon Страницы: 24

Persona Persona M30e

Бренд: Fargo Страницы: 31

External OEMR 2800

Бренд: Dell Страницы: 32

Encryption Key Manager

Бренд: Dell Страницы: 66

External OEMR 2950

Бренд: Dell Страницы: 22

Бренд: Dell Страницы: 10

DVS Simplified Appliance

Бренд: Dell Страницы: 73

Бренд: Dell Страницы: 75

External OEMR 850

Бренд: Dell Страницы: 162

External OEMR 2850

Бренд: Dell Страницы: 176

Бренд: Comdial Страницы: 32

Diabetes Management Software v2.2

Бренд: OneTouch Страницы: 13

ITANIUM ARCHITECTURE - SOFTWARE DEVELOPERS VOLUME 3 REV 2.3

Бренд: Intel Страницы: 1898

Бренд: Nordic Messaging Technologies Страницы: 62

Phone Link Handbook

Бренд: Palm Страницы: 22

Бренд: MACROMEDIA Страницы: 358

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды