Juniper JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010 Скачать руководство пользователя страница 718 | Manualshive

Страница: 718 / 774

background image

■

Example

host1(config-if)#

vlan bulk-config test modify svlan-range 200 250 1 3

■

There is no

no

version.

■

See vlan bulk-config modify.

vlan bulk-config shutdown

■

Use to administratively disable (shut down) a specified VLAN subrange or all
subranges in a VLAN range. The administrative state of a VLAN subrange is
enabled by default.

■

Disabling the VLAN subrange deletes all dynamic VLAN subinterfaces on the
affected subranges. You can use the

show vlan subinterface

command to

monitor the progress of the removal of all dynamic VLAN subinterfaces for the
specified subrange.

■

No dynamic VLAN subinterfaces can subsequently be created for the subrange
until you restore the administrative state to enabled by using the

no vlan

bulk-config shutdown

command.

■

Example

host1(config-if)#

vlan bulk-config test shutdown svlan-range 200 250 1 3

■

Use the

no

version to enable the specified VLAN subrange or all subranges in a

VLAN range.

■

See vlan bulk-config shutdown.

Configuring Static VLAN Subinterfaces Within VLAN Subranges

You can do either of the following on an E Series router:

■

Create a static VLAN subinterface within an existing bulk-configured VLAN
subrange

■

Create a bulk-configured VLAN subrange that includes an existing static VLAN
subinterface

The following sections describe how to perform these tasks.

The example procedures in this section show how to configure static VLAN
subinterfaces within VLAN subranges by using the same loopback interface referenced
by multiple unnumbered IP interfaces. Instead of assigning a different IP address to
each physical interface, the first example assigns an IP address to a loopback interface
(loopback 0). Each physical interface is then configured as an unnumbered IP
interface, referencing the same loopback interface.

Creating Static VLAN Subinterfaces Within VLAN Subranges

You can configure a static VLAN subinterface with a VLAN whose VLAN ID falls within
an existing bulk-configured VLAN subrange.

686

■

Configuring VLAN Dynamic Subinterfaces

JUNOSe 11.1.x Link Layer Configuration Guide

«
...
716
717
718
719
720
...
»

Содержание JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010







































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JUNOSE 11.1.X - LINK LAYER CONFIGURATION 4-7-2010

850DP - Phaser Color Solid Ink Printer

Бренд: Xerox Страницы: 2

Бренд: Alcatel Страницы: 2

Electric Bass Vol. 1—Rock

Бренд: M-Audio Страницы: 4

External OEMR 2800

Бренд: Dell Страницы: 32

Encryption Key Manager

Бренд: Dell Страницы: 66

External OEMR 2950

Бренд: Dell Страницы: 22

Бренд: Dell Страницы: 10

DVS Simplified Appliance

Бренд: Dell Страницы: 73

Бренд: Dell Страницы: 75

External OEMR 850

Бренд: Dell Страницы: 162

External OEMR 2850

Бренд: Dell Страницы: 176

Бренд: Packet8 Страницы: 43

Бренд: EEG Страницы: 16

ENTERPRISE LINUX 4.5.0 -

Бренд: Red Hat Страницы: 434

Over Loud Guitar FX Plug-in Suite

Бренд: Focusrite Страницы: 8

Бренд: Bay Networks Страницы: 88

DIRECTOR MX 2004-GETTING STARTED WITH...

Бренд: MACROMEDIA Страницы: 68

ScanMaker X6 EPP

Бренд: Microtek Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды