ITT PumpSmart PS220, Руководство по конфигурации и эксплуатации

Страница: 268 / 300

PS220 Configuration & Operation Guide
267 PS220
Parameter
Listing
13.91-13.92 AO1 AND AO2 DATA STORAGE Reference the ABB ACS880 Firmware Manual for parameter definition. All ACS880 parameters may not be
supported.
GROUP 14 I/O EXTENSION MODULE 1
DESCRIPTION
14.XX
Parameters
not shown
Refer to the ABB ACS880
Firmware manual
Reference the ABB ACS880 Firmware Manual for parameter definition. All ACS880 parameters may not be
supported.
GROUP 15 I/O EXTENSION MODULE 2
DESCRIPTION
15.XX
Parameters
not shown
Refer to the ABB ACS880
Firmware manual
Reference the ABB ACS880 Firmware Manual for parameter definition. All ACS880 parameters may not be
supported.
GROUP 16 I/O EXTENSION (SLOT 3)
DESCRIPTION
16.01
MODULE 3 TYPE Activates (and specifies the type of) I/O extension module 1. NOTE: PumpSmart only sup- ports the FIO-11 module.
Select FIO-11 here.
16.02
MODULE 3 LOCATION Specifies the slot on the control unit of the drive into which the I/O extension module is installed. The PS220
PumpSmart must have the FIO-11 module physically loaded into slot 3 only.
16.03
MODULE 3 STATUS Displays the status of I/O extension module in slot 3. This should display FIO-11 if it is installed and configured.
16.XX
Parameters
not shown
Refer to the ABB ACS880
Firmware manual
Reference the ABB ACS880 Firmware Manual for parameter definition. All ACS880 parameters may not be
supported.
GROUP 19 OPERATING MODE
DESCRIPTION
19.01
ACTUAL CONTROL MODE
Displays the operating mode currently used. This is a read only parameter. Default value is Speed. (Speed, Torque)
19.17
LOCAL CONTROL DISABLE Enables/disables local control (start and stop buttons on the control panel, and the local controls on the PC tool).
WARNING! Before disabling local control, ensure that the control panel is not needed for stopping the drive.
19.20
SCALAR CONTROL REFERENCE
UNIT
Selects the reference type for scalar motor control mode. Default is RPM. (RPM, Hz)
19.200
EXT 1 CONTROL MODE Selects the external 1 control mode. Default is Speed. Torque is used for SmartControl
19.XX
Parameters
not shown
Refer to the ABB ACS880
Firmware manual
Reference the ABB ACS880 Firmware Manual for parameter definition. All ACS880 parameters may not be
supported.
GROUP 20 START/STOP?DIRECTION
DESCRIPTION
20.XX
Parameters
not shown
Refer to the ABB ACS880
Firmware manual
Reference the ABB ACS880 Firmware Manual for parameter definition. All ACS880 parameters may not be
supported.
GROUP 21 START/STOP MODE
DESCRIPTION
21.18
Auto restart time The time allowed for the motor to restart after a short supply power failure when using Digital Inputs for starting and
stopping. Setting to 0 seconds will allow for auto restarting. 74.02 Must be On.
The function restarts the drive automatically and continues operation after a supply
break. Make sure that no dangerous situations can occur.
21.XX
Parameters
not shown
Refer to the ABB ACS880
Firmware manual
Reference the ABB ACS880 Firmware Manual for parameter definition. All ACS880 parameters may not be
supported.
GROUP 22 SPEED REFERENCE SELECTION
DESCRIPTION
22.XX
Parameters
not shown
Refer to the ABB ACS880
Firmware manual
Reference the ABB ACS880 Firmware Manual for parameter definition. All ACS880 parameters may not be
supported.
GROUP 23 SPEED RAMP SETUP
DESCRIPTION
23.12
ACCELERATION TIME Defines acceleration time. (Range = 0-1800 sec). Default is 5 sec.
23.13
DECELERATION TIME Defines the deceleration time. (Range = 0-1800 sec). Default is 5 sec.
23.XX
Parameters
not shown
Refer to the ABB ACS880
Firmware manual
Reference the ABB ACS880 Firmware Manual for parameter definition. All ACS880 parameters may not be
supported.
GROUPS
24 - 26
Refer to the ABB ACS880
Firmware manual
Reference the ABB ACS880 Firmware Manual for parameter definition. All ACS880 parameters may not be
supported.
GROUP 28 FREQUENCY REFERENCE
CHAIN
DESCRIPTION
28.52
CRITICAL FREQUENCY 1 LOW Defines the low limit for critical frequency 1. Note: This value must be less than or equal to the value of 28.53
Critical frequency 1 high. Default value is 0. (0-500.00 Hz)
28.53
CRITICAL FREQUENCY 2 HIGH
Defines the high limit for critical frequency 1. Note: This value must be greater than or equal to the value of 28.52
Critical frequency 1 high. Default value is 0. (0-500.00 Hz)
28.54
CRITICAL FREQUENCY 2 LOW
Defines the low limit for critical frequency 2. Note: This value must be less than or equal to the value of 28.55
Critical frequency 2 high. Default value is 0. (0-500.00 Hz)
28.55
CRITICAL FREQUENCY 2 HIGH Defines the high limit for critical frequency 2. Note: This value must be greater than or equal to the value of 28.54
Critical frequency 2 low. Default value is 0. (0-500.00 Hz)
28.56
CRITICAL FREQUENCY 3 LOW Defines the low limit for critical frequency 3. Note: This value must be less than or equal to the value of 28.57
Critical frequency 1 high. Default value is 0. (0-500.00 Hz)
28.57
CRITICAL FREQUENCY 3 HIGH Defines the high limit for critical frequency 3. Note: This value must be greater than or equal to the value of 28.56
Critical frequency 3 high. Default value is 0. (0-500.00 Hz)
28.XX
Parameters
not shown
Refer to the ABB ACS880
Firmware manual
Reference the ABB ACS880 Firmware Manual for parameter definition. All ACS880 parameters may not be
supported.
WARNING