ITT PumpSmart PS220, Руководство по конфигурации и эксплуатации

Страница: 253 / 300

PS220 Configuration & Operation Guide
PS220 252
Fault T
racing
have been added to piping.
•
Check discharge piping static height compared to TDH
output of the pump.
E211 CONDITION 2 LO
WARNING
Warning Only
The signal level for Condition 2
fallen below the 80. 12 COND 2
WRN LIM LO.
• Investigate cause of condition
• Check parameter settings of 80.12
E212 PIPE CLEAN TIME OUT
Warning Only Unable to complete the pipe
clean sequence.
• Check parameter settings of 83.22 and 83.23
• Verify that the PS220 is not current limited and is able
to reach maximum speed set up in 30.12
• Verify that another warning or fault is not active. This
can be seen in the event log.
E213 SPEED OVERRIDE
Warning Only The PS220 Speed Override
function is active
• The Speed Override function is running. Waring message
only. Check that Speed Override Pump protection is
active (79.04) if required to protect the pump.
E214 CONDITION 2 HI WARNING
Warning Only The signal level for Condition 1
has exceeded the
80.11 COND 2 WRN LIM HI.
• Investigate cause of condition
• Check parameter settings of 80.06
E215 PUMP CLEANING
RUNNING
Warning Only
Pump clean sequence is being
executed
• Check parameter 83.01 and 83.02 to verify that the
cleaning sequence is executing as intended.
E216 PUMP CLEANING (RT)
RUNNING
Warning Only
The Pump Cleaning sequence
has re-executed. It did not
unclog in the previous try.
• PS220 try will continue to run the sequence until the
pump is unclogged. If the number of cycles set up in
83.06 has exceeded and the pump is still clogged, the
PS220 will respond based on parameter 83.18.
E217 PUMP CLEANING
WARNING
Pump clean sequence is being
executed
• Check parameter 83.01 and 83.02 to verify that the
cleaning sequence is executing as intended.
E218 PIPE CLEANING (RT)
RUNNING
Warning Only
The Pipe Clean Sequence has
initiated an automatic retry.
Warning message only. No action is necessary. Issue a
stop command to end the Pump Cleaning Sequence
completely.
E219 TOTAL SYSTEM FLOW
COMPLETED
Warning Only
The pump has completed
pumping the total volume set in
parameter 84.01.
• The flow totalizing function is setup by parameters
84.01and 84.02.
• Verify that the pumped volumes are based on the
above settings ( within the stated Ps220’s published
accuracy limits)
E220 COND 2 HI ALARM
Warning only The signal level for Condition 2
has exceeded the
80.14 COND 2 ALAMR LIM HI.
• Investigate cause of condition
• Check parameter settings of 80.13 and 80.14
E221 CONDITION SLEEP
Warning Only A Condition 1 or Condition 2
value exceeded the alarm limits,
and the Condition Sleep
Function is active.
• Investigate cause of condition
• Check parameter settings of 80.0,7 80.08,80.09,
80.13, 80.14 and 80.15
E222 COND 2 LO ALARM
Warning Only The signal level for Condition 2
has fallen below 80.15 COND 1
ALAMRM LIM LO.
• Investigate cause of condition
• Check parameter settings of 80.13 and 80.15
E223 PID LOW DEMAND
Warning Only The PS220 requires operating at
a speed below minimum speed
to maintain the set- point.
• Check for reference not set to 0
• Minimum speed 30.11 is set to high for the
application. The Pump may be oversized for the
system.
• Check that Sleep Mode (75.03) is not set to disabled.
• Check 79.16 is set to match 75.03
E224 START DELAY ACTIVE
Warning Only Start delay has been
enabled.
• No action required.
• Once delay period is complete the pump will start
running.
E225 PRIMING ON
Warning Only Pump is running the priming
function. It will run at full speed
with all logic and protection
turned off internally.
Warning only. It will run every time the start is received.
E226 STAGE TIMEOUT Alarm
Warning Only The stage requested did occur. • Re issue a start command on this pump
• Cycle the power to the drive.
E21A BYPASS VALVE OPEN
Warning Only The PS220’s minimum flow
bypass valve control has
triggered the signal for a
relay to open a bypass
valve.
• Warning message only.
• NOTE: When the bypass closes there will not be a
message stating this.
E21B PIPE CLEAN RUNNING
Warning Only The PS220 is executing a pipe
clean sequence.
• Verify that the sequence if operating based on
parameter settings 83.21, 83.22 & 83.23
E21C PIPE FILL RUNNING
Warning Only The PS220 Pipe-Fill function is
running
• Warning only. No action required
E21D PIPE FILL The PS220 Pipe-Fill function is
running
Warning only. No action required
E21E COND 1 HI ALARM
Warning Only The signal level for Condition
1 has exceeded 80.08 COND
1 ALAMRM LIM HI
• Investigate cause of condition
• Check parameter settings of 80.07 and 80.08
E21F COND 1 LO ALARM
Warning only The signal level for Condition 1
has fallen below 80.09 COND 1
ALAMRM LIM LO.
• Investigate cause of condition
• Check parameter settings of 80.07 and 80.09