HNC Electric HV580L-004G3 Скачать руководство пользователя

Страница: 93 / 202

HV580L Series Frequency Inverter

parameters are P2-03 and P2-04.

• If the running frequency is between P2-02 and P2-05, the speed loop PI parameters are obtained from the

linear switchover between the two groups of PI parameters, as shown in Figure 6-2.

Figure 6-2: Relationship between running frequencies and PI parameters

The speed dynamic response characteristics in vector control can be adjusted by setting the proportional gain

and integral time of the speed regulator.

To achieve a faster system response, increase the proportional gain and reduce the integral time. Be aware

that this may lead to system oscillation.

The recommended adjustment method is as follows:

If the factory setting cannot meet the requirements, make proper adjustment. Increase the proportional gain

first to ensure that the system does not oscillate, and then reduce the integral time to ensure that the system

has quick response and small overshoot.

Note: Improper PI parameter setting may cause too large speed overshoot, and over voltage fault may even

occur when the overshoot drops.

P2-06

Vector control slip gain

Default

100%

Setting Range

50%

～

200%

For SFVC, it is used to adjust speed stability accuracy of the motor. When the motor with load runs at a very

low speed, increase the value of this parameter; when the motor with load runs at a very large speed,

decrease the value of this parameter.

For CLVC, it is used to adjust the output current of the AC drive with same load.

P2-07

Time constant of speed

loop filter

Default

0.000s

Содержание HV580L-004G3











































































































































































































Результаты поиска

Содержание HV580L-004G3

Отзывы:

Похожие инструкции для HV580L-004G3

Бренды по названию

Популярные бренды

HNC Electric HV580L-004G3, Руководство пользователя

Результаты поиска

Содержание HV580L-004G3

Отзывы:

Похожие инструкции для HV580L-004G3

Бренды по названию

Популярные бренды