manualshive.com logo in svg

Dräger Infinity Acute Care System M540, Инструкция по эксплуатации

Поделиться
Скачать
Dräger Infinity Acute Care System M540 Скачать руководство пользователя страница 204

ECG, arrhythmia, and ST segment

204

Instructions for use – Infinity Acute Care System – Monitoring Applications VG6.n

Patient preparation for ECG monitoring

The following tips provide optimal ECG monitoring 
results but must never replace hospital-approved 
practices or manufacturer’s recommendations.

Follow hospital procedures for proper skin 
preparation. Dräger recommends Ag/AgCl 
disposable electrodes. Never use disposable 
electrodes after their expiration date and make sure 
that there is enough gel and that the gel has not 
dried out. 

P and T waves with amplitudes exceeding 0.2 mV 
can be interpreted as QRS complexes. To allow 
detection of low heart rate conditions under these 
circumstances, place the lead with the highest R 
wave in channel ECG1. If P and T waves continue 
to be misinterpreted, reposition the electrodes or 
use an SpO

2

 sensor to monitor the pulse rate.

To maintain a clear signal, change electrodes every 
24 to 48 hours or more often when the following 
occurs:

– ECG signal degradation

– Excessive patient perspiration

– Skin irritation

Consider the following when selecting electrode 
sites:

– Surgery –

 

keep electrodes as far from the 

surgical site as possible, while maintaining a 
clinically useful lead configuration. Place the 
cable and lead wires as far from the ESU as 
possible and perpendicular to the ESU cables.

– Burn Patients

 

–

 

use sterile electrodes. Clean 

the equipment thoroughly and follow hospital 
infection control procedures.

– Incorrect placement of electrodes affects the 

signal quality.

Electrosurgery

Integrated ESU suppression improves the 
performance of the monitor during electrosurgery, 
reduces noise on ECG waveforms, and protects 
the patient from burns. 

To minimize interference from the 
electrosurgical unit

Select the heart rate parameter field.

or

1

Select 

Sensor parameters...

 from the main 

menu bar. 

2

Select the 

Settings 2

 tab (if not already 

selected).

3

Select 

ESU

 next to the 

Filter

 selection.

NOTE

ESU mode provides better HR performance in the 
presence of electrosurgical interference, but with 
possible ECG R-wave amplitude reduction on 
narrow complexes.

NOTE

12-lead monitoring is not available when the ESU 
filter is enabled. Likewise, the ESU filter selection 
is not available when you are using 12-lead 
monitoring.

If the 

Filter

 selection is set to 

ESU

 at the Cockpit 

and you switch to a 12-lead ECG at the M540, 
the 

Filter

 setting automatically changes to 

Monitor

 at the Cockpit. 

Содержание Infinity Acute Care System M540



































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды